Work Health and Safety (How to Safely Remove Asbestos) Code of Practice 2015 (Cth)
Work Health and Safety (How to Safely Remove Asbestos) Code of Practice 2015
made under the
Work Health and Safety Act 2011, section 274 (Approved Codes of Practice)
1 Name of instrument
This instrument is the Work Health and Safety (How to Safely Remove Asbestos) Code of Practice 2015.
2 Commencement
This instrument commences on the day after it is registered on the Federal Register of Legislative Instruments.
3 Code of Practice Approval
I approve the How to Safely Remove Asbestos Code of Practice. I am satisfied that this code of practice was developed by a process described in section 274(2) of the Work Health and Safety Act 2011.
Michaelia Cash
Minister for Employment
18 March 2016
Date
HOW TO SAFELY
REMOVE ASBESTOS
CODE OF PRACTICE
TABLE OF CONTENTS
FOREWORD
1. INTRODUCTION
1.1 Who has health and safety duties when removing asbestos?
1.2 The meaning of key terms
1.3 Licence requirements for asbestos removal work
1.4 Health monitoring duties
2. DUTIES FOR REMOVAL WORK THAT DOES NOT REQUIRE A LICENCE
2.1 Training workers about asbestos or ACM
3. DUTIES FOR LICENSED ASBESTOS REMOVAL WORK
3.1 Asbestos removalist supervisor to be present or readily available
3.2 Certification and training
3.3 Informing parties of the licensed asbestos removal
3.4 Obtaining the asbestos register
3.5 Preparing an asbestos removal control plan
3.6 Notifying the regulator of the licensed asbestos removal work
3.7 Limiting access, displaying signs and installing barricades
3.8 Decontamination
3.9 Waste containment and disposal
3.10 Clearance inspection
3.11 Air monitoring
3.12 Removing friable asbestos
4. CONTROLS APPLICABLE TO ALL TYPES OF ASBESTOS REMOVAL
4.1 Identifying hazards
4.2 Indicating the asbestos removal areas
4.3 Wet and dry methods
4.4 Tools and equipment
4.5 Personal protective equipment
4.6 Decontamination
4.7 Laundering clothing
4.8 Waste containment and disposal
5. USING AN ENCLOSURE DURING LARGE SCALE REMOVAL WORK
5.1 Designing and installing an enclosure
5.2 Testing an enclosure
5.3 Information on pressure exhaust units (negative units)
6. METHODS FOR SMALL SCALE REMOVAL WORK
6.1 Mini-enclosure
6.2 Glove bag asbestos removal work
6.3 Wrap and cut asbestos removal method
7. CONTROLS FOR SPECIFIC ASBESTOS REMOVAL WORK
7.1 Removing asbestos-contaminated soil
7.2 Removing friable asbestos from hot surfaces
7.3 Removing asbestos in plant and pipes or pits
APPENDIX A – ASBESTOS REMOVAL CONTROL PLAN CONTENTS
APPENDIX B – RESPIRATORY PROTECTIVE EQUIPMENT
APPENDIX C – EXAMPLE OF A CLEARANCE CERTIFICATE
APPENDIX D – EXAMPLES OF ASBESTOS REMOVAL WORK
FOREWORD
This Code of Practice on how to safely remove asbestos is an approved code of practice under section 274 of the Work Health and Safety Act (the WHS Act).
An approved code of practice is a practical guide to achieving the standards of health, safety and welfare required under the WHS Act and the Work Health and Safety Regulations (the WHS Regulations).
A code of practice applies to anyone who has a duty of care in the circumstances described in the code. In most cases, following an approved code of practice would achieve compliance with the health and safety duties in the WHS Act, in relation to the subject matter of the code. Like regulations, codes of practice deal with particular issues and do not cover all hazards or risks that may arise. The health and safety duties require duty holders to consider all risks associated with work, not only those for which regulations and codes of practice exist.
Codes of practice are admissible in court proceedings under the WHS Act and Regulations. Courts may regard a code of practice as evidence of what is known about a hazard, risk or control and may rely on the code in determining what is reasonably practicable in the circumstances to which the code relates.
The WHS Act and the Regulations may be complied with by following another method, such as a technical or an industry standard, if it provides an equivalent or higher standard of work health and safety than the code.
An inspector may refer to an approved code of practice when issuing an improvement or prohibition notice.
This Code of Practice has been developed by Safe Work Australia as a model code of practice under the Council of Australian Governments’ Inter-Governmental Agreement for Regulatory and Operational Reform in Occupational Health and Safety for adoption by the Commonwealth, state and territory governments.
A draft of this Code of Practice was released for public consultation on 7 December 2010 and was endorsed by the Workplace Relations Ministers’ Council on 10 August 2011.
Scope and application
This Code provides practical guidance for persons conducting a business or undertaking who have duties under the WHS Act and WHS Regulations to safely remove asbestos from all workplaces including structures, plant and equipment.
A person conducting a business or undertaking may be an asbestos removalist who may carry out asbestos removal work that does not require a licence, Class A asbestos removal work or Class B asbestos removal work. This could include both asbestos removal companies and those persons who may carry out small asbestos removal jobs and may not have an asbestos licence, for example tradespersons.
It is recommended that other persons with responsibility—for example, a person conducting a business or undertaking who commissions asbestos removal work at a workplace (person who commissions removal work)—should read this Code to ensure they are aware of mandatory requirements.
This Code may also be used by workers and their health and safety representatives and other persons affected by asbestos removal work, for example neighbours.
It is important to read the Code of Practice: How to Manage and Control Asbestos in the Workplace, as it provides specific guidance on identifying asbestos or ACM in the workplace, determining whether removal is the best control option and implementing other control measures if removing asbestos is not the most appropriate action to take.
Some chapters of this Code will apply to asbestos that is present in domestic premises where the premises becomes a workplace.
How to use this Code of Practice
In providing guidance, the word ‘should’ is used in this Code to indicate a recommended course of action, while ‘may’ is used to indicate an optional course of action.
This Code also includes various references to provisions of the WHS Act and Regulations to provide context with legal requirements. These references are not exhaustive. The words ‘must’, ‘requires’ or ‘mandatory’ indicate that these legal requirements exist and must be complied with.
INTRODUCTION
1.1 Who has health and safety duties when removing asbestos?
The WHS Act requires all persons who conduct a business or undertaking to ensure, so far as is reasonably practicable, that workers and other persons are not put at risk from work carried out as part of the business or undertaking.
The person conducting a business or undertaking must also ensure so far as is reasonably practicable that exposure of a person at the workplace to airborne asbestos is eliminated. If this is not reasonably practicable, the exposure must be minimised so far as is reasonably practicable. The exposure standard for asbestos must not be exceeded.
The WHS Regulations include specific obligations for a number of duty holders in relation to safely removing asbestos. These duties are summarised in Chapters 2 and 3 of this Code.
Officers, such as company directors, have a duty to exercise due diligence to ensure that the business or undertaking complies with the WHS Act and WHS Regulations. This includes taking reasonable steps to ensure that the business or undertaking has and uses appropriate resources and processes to eliminate or minimise risks associated with asbestos.
Workers have a duty to take reasonable care for their own health and safety and that they do not adversely affect the health and safety of other persons. They must comply with any reasonable instruction and cooperate with any reasonable policy or procedure relating to health and safety at the workplace. If PPE is provided by the person conducting the business or undertaking, the worker must use it in accordance with information, instruction and training provided on their use.
Consultation
There are a number of specific duties in both the WHS Act and WHS Regulations that require consultation with others throughout the asbestos removal process. Communicating and consulting with a range of people helps to increase the awareness of the potential health and safety risks of asbestos.
An asbestos removalist must consult with persons that may be affected by the asbestos removal work, as well as other responsible persons at the workplace, to eliminate or minimise the exposure to the risks associated with asbestos, for example site management or the project manager, workers, health and safety representatives, contractors, building occupants and others. This also includes speaking with neighbours and other businesses where the asbestos removal work is occurring at domestic premises.
Further guidance on consultation is available in the Code of Practice: Work Health and Safety Consultation, Cooperation and Coordination.
1.2 The meaning of key terms
Airborne asbestos means any fibres of asbestos small enough to be made airborne. For the purposes of monitoring airborne asbestos fibres, only respirable fibres are counted.
Asbestos means the asbestiform varieties of mineral silicates belonging to the serpentine or amphibole groups of rock forming minerals, including actinolite asbestos, grunerite (or amosite) asbestos (brown), anthophyllite asbestos, chrysotile asbestos (white), crocidolite asbestos (blue) and tremolite asbestos or a mixture of any of these.
Asbestos containing material (ACM) means any material or thing that, as part of its design, contains asbestos.
Asbestos-contaminated dust or debris (ACD) means dust or debris that has settled within a workplace and is (or is assumed to be) contaminated with asbestos.
Asbestos-related work means work involving asbestos (other than asbestos removal work to which Part 8.7 of the WHS Regulations applies) that is permitted under the exceptions set out in regulation 419(3), (4) and (5).
Asbestos removalist means a person conducting a business or undertaking who carries out asbestos removal work.
Asbestos removal work means:
work involving the removal of asbestos or ACM
Class A asbestos removal work or Class B asbestos removal work as outlined in Part 8.10 of the WHS Regulations.
Competent person in relation to carrying out clearance inspections under regulation 473 means a person who has acquired through training or experience the knowledge and skills of relevant asbestos removal industry practice and holds a certification in relation to the specified VET course for asbestos assessor work or a tertiary qualification in occupational health and safety, occupational hygiene, science, building, construction or environmental health. For all other purposes, competent person means a person who has acquired through training, qualification or experience, the knowledge and skills to carry out the task.
Exposure standard for asbestos is a respirable fibre level of 0.1 fibres/ml of air measured in a person’s breathing zone and expressed as a time weighted average fibre concentration calculated over an eight-hour working day and measured over a minimum period of four hours in accordance with:
the Membrane Filter Method
a method determined by the relevant regulator.
Friable asbestos means material that is in a powder form or that can be crumbled, pulverised or reduced to a powder by hand pressure when dry, and contains asbestos.
GHS means Globally Harmonised System of Classification and Labelling of Chemicals.
Licensed asbestos assessor means a person who holds an asbestos assessor licence.
Licensed asbestos removalist means a person conducting a business or undertaking who is licensed under the WHS Regulations to carry out Class A or Class B asbestos removal work.
Naturally occurring asbestos (NOA) means the natural geological occurrence of asbestos minerals found in association with geological deposits including rock, sediment or soil.
Non-friable asbestos means material containing asbestos that is not friable asbestos, including material containing asbestos fibres reinforced with a bonding compound.
Respirable asbestos means an asbestos fibre that:
is less than 3 micron metres (µm) wide
more than 5 micron metres (µm) long
has a length to width ratio of more than 3:1.
1.3 Licence requirements for asbestos removal work
R. 458 A person conducting a business or undertaking who commissions the removal of asbestos at the workplace must ensure asbestos removal work is carried out only by a licensed asbestos removalist who is appropriately licensed to carry out the work, unless specified in the WHS Regulations that a licence is not required.
There are two types of licences: Class A and Class B. The type of licence required will depend on the type and quantity of asbestos or ACM that is being removed at a workplace.
| Type of licence | What asbestos can be removed? |
| Class A | Can remove any amount or quantity of asbestos or ACM, including: · any amount of friable asbestos or ACM · any amount of ACD · any amount of non-friable asbestos or ACM. |
| Class B | Can remove: · any amount of non-friable asbestos or ACM Note: A Class B licence is required for removal of more than 10 m2 of non‑friable asbestos or ACM but the licence holder can also remove up to 10 m2 of non-friable asbestos or ACM. · ACD associated with the removal of non-friable asbestos or ACM. Note: A Class B licence is required for removal of ACD associated with the removal of more than 10 m² of non-friable asbestos or ACM but the licence holder can also remove ACD associated with removal of up to 10m² of non‑friable asbestos or ACM. |
| No licence required | Can remove: · up to 10 m2 of non-friable asbestos or ACM · ACD that is: o associated with the removal of less than 10 m2 of non-friable asbestos or ACM o not associated with the removal of friable or non-friable asbestos and is only a minor contamination. |
Examples where a licence is not required to perform asbestos removal work
A single asbestos cement sheet must be removed to install an air conditioner. The sheet is 2 m2 in total. This job may be performed by a company that is not a licensed asbestos removalist, observing the requirements outlined in Chapter 2.
A self-employed person is required to remove an asbestos cement eave to enable access for pipes. The asbestos cement eave is 1.6 m2 in total. This job may be performed by the self-employed person who is not a licensed asbestos removalist, observing the requirements outlined in Chapter 2.
Examples of Class A or B licensed asbestos removal work
A person is engaged to remove asbestos cement sheets from a factory toilet block. The material to be removed is non-friable asbestos. The area to be removed is 12 m² in total so the person must be a licensed asbestos removalist and the material to be removed is non-friable so the work can be done by a Class A or Class B licensed asbestos removalist.
A company is required to remove 0.5 m³ (cubic metres) of asbestos lagging from a pipe in order to carry out maintenance work. This involves the removal of friable asbestos. A Class A licensed asbestos removalist is required to do this work.
Licensed asbestos assessor
The WHS Regulations require that a person must hold an asbestos assessor licence to conduct the following:
air monitoring for Class A asbestos removal work
clearance inspections for Class A asbestos removal work
issuing clearance certificates in relation to Class A asbestos removal work.
A licensed assessor can also carry out a number of other tasks including identifying asbestos, carrying out a risk assessment or reviewing an asbestos register.
1.4 Health monitoring duties
R. 435-444 A person conducting a business or undertaking to ensure health monitoring is provided to a worker if they are carrying out licensed asbestos removal work, other ongoing asbestos removal work or asbestos-related work and is at risk of exposure to asbestos when carrying out the work.
Health monitoring includes a medical examination to provide an initial baseline medical assessment.
Health monitoring must include the following (unless another form of health monitoring is recommended by a registered medical practitioner):
consideration of the worker’s demographic, medical and occupational history
consideration of records of the worker’s personal exposure
a physical examination of the worker with emphasis on the respiratory system, including standardised respiratory function tests, unless another form of health monitoring is recommended by a registered medical practitioner.
Workers must be informed of any health monitoring requirements before the worker carries out work that may expose them to asbestos.
When should health monitoring occur?
Where a worker is at risk of exposure to asbestos due to work other than licensed asbestos removal, health monitoring must also be undertaken. Examples of work where there is a risk of exposure include ongoing unlicensed removal work, undertaking maintenance work on ACM regularly as part of another job (for instance, electricians or building maintenance staff in older buildings) and carrying out asbestos-related work. The need for health monitoring for these workers should be determined on the basis of:
the potential for exposure
the frequency of potential exposure
the duration of the work being undertaken.
If a worker is carrying out licensed asbestos removal work, the health monitoring must be conducted prior to the worker commencing the work. Health monitoring should also be provided to the worker at regular intervals after commencing the asbestos-related work but at least once every two years.
Who can carry out health monitoring?
Health monitoring must be carried out under the supervision of a registered medical practitioner with the relevant competencies. Prior to deciding who the registered medical practitioner will be, the person conducting a business or undertaking must consult the worker.
Who pays for health monitoring?
The person conducting a business or undertaking must pay all expenses relating to health monitoring.
Where there are two or more persons that have a duty to provide health monitoring to a worker, they may choose that one person organises health monitoring (known as the person who commissions the health monitoring), however the costs must be shared equally between each person unless they agree otherwise.
What information must be provided to the register medical practitioner?
The person who commissions health monitoring must provide the following information to the registered medical practitioner:
their name and address
the name and date of birth of the worker
a description of the work the worker is, or will be, carrying out that has triggered the requirement for health monitoring
whether the worker has started the work or, if the worker has commenced carrying out the work, how long this has been for.
Health monitoring report
A person who commissions health monitoring must take all reasonable steps to obtain a report from the registered medical practitioner as soon as practicable after the monitoring is carried out.
The health monitoring report must include the following information:
the name and date of birth of the worker
the name and registration number of the registered medical practitioner
the name and address of the person conducting the business or undertaking who commissioned the health monitoring
the date of the health monitoring
any advice that test results indicate the worker may have contracted a disease, injury or illness as a result of carrying out the work that triggered the need for health monitoring
any recommended remedial measures, including whether the worker can continue to carry out the work
whether medical counselling is required for the worker.
That person must also give a copy of the report, as soon as reasonably possibly after obtaining it from the medical practitioner, to:
the worker
the regulator, if the report contains:
oany test results that indicate the worker may have contracted a disease, injury or illness as a result of the work that triggered the need for health monitoring
oany recommended remedial measures, including whether the worker can continue to carry out the work
all other persons conducting a business or undertaking who have a duty to provide health monitoring for that worker.
Reports must be kept as a confidential record for at least 40 years after the record is made and identified as a formal record for the particular worker. The report and results must not be disclosed to anyone unless the worker has provided their written consent. However, if the person was releasing the record under a duty of professional confidentiality, the worker’s written consent is not required.
DUTIES FOR REMOVAL WORK THAT DOES NOT REQUIRE A LICENCE
Removal of asbestos by a person who does not hold a Class A or Class B asbestos removal licence is permitted if the asbestos being removed is:
10 m² or less of non-friable asbestos (approximately the size of a small bathroom)
ACD that is not more than a minor contamination and is associated with the removal of 10 m² or less of non-friable asbestos.
Friable asbestos materials must not be removed by a person who does not have a Class A asbestos licence.
A worker carrying out asbestos removal work, including a self-employed person conducting a business or undertaking, must be trained in the identification and safe handling of asbestos prior to carrying out asbestos removal work without a licence. An asbestos awareness course or the non‑friable removal unit of competency would be considered appropriate training.
This allows a person (for example, a plumber) to remove small amounts of non-friable asbestos and replace it with non-asbestos alternatives if they come across it during renovations, refurbishments, or service and maintenance work. However, this person must still use safe working methods to ensure the work is not creating a risk to the health and safety of persons at the workplace.
The WHS Regulations require a person who is carrying out asbestos removal work without a licence to comply with the duties outlined in Chapter 4 of this Code and also with some of the duties in Chapter 3 of this Code. These duties are summarised below:
obtain a copy of the asbestos register for a workplace unless the work is being carried out at a domestic premises (refer to Section 3.4)
identity hazards at the workplace (refer to Section 4.1)
ensure signs and barricades are erected to indicate and delineate the asbestos work area (refer to Sections 3.7 and 4.2)
use the wet method to removal asbestos where reasonably practicable (refer to Section 4.3)
ensure the correct tools, equipment and PPE is used (refer to Sections 4.4 and 4.5)
ensure decontamination facilities are available (refer to Sections 3.8 and 4.6)
contain and label asbestos waste and dispose of it as soon as reasonably practicable (refer to Sections 3.9 and 4.8)
ensure that PPE and clothing used in asbestos removal work and contaminated with asbestos is handled in accordance with the WHS Regulations (refer to Sections 3.9, 4.5 and 4.6)
Although it is not mandatory for the person to prepare an asbestos removal control plan for this type of asbestos removal work, it may be beneficial to do so to ensure the work is being carried out safely. Refer to Section 3.5 for further information on an asbestos removal control plan.
It is also not mandatory to conduct air monitoring however, an independent licensed asbestos assessor or competent person can carry out it out in these situations. Refer to Section 3.11 for further information on air monitoring.
1.5
2.1 Training workers about asbestos or ACM
R. 39 A person conducting a business or undertaking must ensure that information, training and instruction provided to a worker is suitable and adequate, having regard to:
the nature of the work carried out by the worker
the nature of the risks associated with the work at the time the information, training or instruction is provided, and
the control measures implemented.
The person must, so far as is reasonably practicable, ensure that the information, training and instruction is provided in a way that is readily understandable by any person to whom it is provided.
R. 445 A person conducting a business or undertaking must ensure workers who they reasonably believe may be involved in asbestos removal work in the workplace or the carrying out of asbestos-related work are trained in the identification, safe handling and suitable control measures for asbestos and ACM.
This training may include the following topics:
purpose of the training
health risks of asbestos
types, uses and likely presence of asbestos in the workplace
persons conducting a business or undertaking and the worker’s roles and responsibilities under the asbestos management plan
where the asbestos register is located, how it can be accessed and how to understand the information contained in it
processes and safe work procedures to be followed to prevent exposure, including exposure from any accidental release of airborne asbestos
where applicable, the correct use of PPE including respiratory protective equipment (RPE)
the implementation of control measures and safe work methods to eliminate or minimise the risks associated with asbestos to limit the exposure to workers and other persons
exposure standard and control levels for asbestos
purpose of any exposure monitoring or health monitoring that may occur.
This training is more general than the training that a worker undertaking licensed asbestos removal work would receive. Workers who are undertaking licensed asbestos removal work are required to complete specific units of competency. Refer to Section 3.2 for further information.
Records of all training must be kept while the worker is carrying out the work and for five years after the day the worker stops carrying out the work. These records must also be available for inspection by the regulator.
DUTIES FOR LICENSED ASBESTOS REMOVAL WORK
Licensed asbestos removal work can differ greatly depending on the type, quantity and condition of the asbestos or ACM being removed. There are a number of duties in the WHS Regulations to ensure licensed asbestos work is carried out safely and without releasing airborne asbestos and exposing workers and other persons.
A summary of the specific duties in the WHS Regulations are:
ensuring an asbestos removalist supervisor is readily available or present when the work is being carried out (R.459)
providing appropriate training and ensuring the asbestos removal worker has undertaken the relevant units of competencies associated with the asbestos removal (R.460-461)
telling various parties about the asbestos removal and providing them with appropriate information (R.462 and R.467-468)
obtaining the workplace’s asbestos register (R.463)
preparing an asbestos removal control plan (R.464-465)
notifying the regulator about the work before it starts (R.466)
displaying signs and labels in the asbestos work area (R.469)
limiting access to the asbestos work area (R.470)
ensuring appropriate decontamination facilities are in place (R.471)
ensuring waste containment and disposal procedures are in place (R.472)
ensuring clearance inspections are conducted and issuing clearance certificates (R.473-474)
ensuring air monitoring is conducted, where appropriate (R.475-477).
These requirements apply to a number of duty holders including the licensed asbestos removalist, the person who commissioned the asbestos removal work, and the person with management and control of the workplace. The duties are explained further below.
3.1 Asbestos removalist supervisor to be present or readily available
When licensed asbestos removal work is being carried out at a workplace, an asbestos removal supervisor must oversee the work. The licensed asbestos supervisor must have a certification appropriate to the type of licensed asbestos removal work.
If the asbestos removal work requires a Class A licence, for example removing friable asbestos, the asbestos removal supervisor must be present at the asbestos removal area whenever the work is being carried out.
However, if the asbestos removal work requires a Class B licence, for example non-friable asbestos that is more than 10 m², then the asbestos removal supervisor must be readily available to a worker who is carrying out the work whenever it is being carried out. For example, if the supervisor is contactable by phone and able to arrive at the workplace within 20 minutes, this would be regarded as accessible.
Where the asbestos removal work requires a Class B licence and it is being carried out by a self-employed person working alone, for example a plumber removing more than 10 m² of AC sheeting, the person must hold the competency of a worker for non-friable asbestos removal and the competency of a supervisor for non-friable asbestos removal.
3.2 Certification and training
Certification
A licensed asbestos removalist must not direct or allow a worker to carry out licensed asbestos removal work unless they are satisfied the worker holds a certification that is relevant to the class of licensed asbestos removal work they will be carrying out.
Workers (including the asbestos removal supervisors) who are carrying out licensed asbestos removal work are required to acquire a certification by completing units of competencies to show they have the relevant training to be able to remove asbestos. The units of competency completed by the person will determine what type of asbestos work they can carry out. Asbestos removal supervisors will have additional units of competency to complete.
Registered training organisations conduct training and education for the specific unit of competency for both Class A and Class B asbestos removal work as well as the asbestos removal supervisor certification. The Class B removal unit of competency must be completed before the Class A removal unit of competency.
Training
A licensed asbestos removalist must provide appropriate training to a worker carrying out licensed asbestos removal work at the workplace to ensure the work is carried out in accordance with the asbestos removal control plan for the workplace.
This is additional training to the general training that is provided on the identification and safe handling of asbestos and the appropriate controls referred to in section 6.3 of the Code of Practice: How to Manage and Control Asbestos in the Workplace.
A worker who is carrying out licensed asbestos removal work must receive training that is designed specifically for the workplace where the work is being or is to be carried out. This should occur before the commencement of each asbestos removal job. The training should include:
the nature of the hazards and risks
how asbestos can affect a person’s health
the risk from exposure to airborne asbestos
the control measures in place and maintenance of the asbestos removal control plan for that job
the methods and equipment that will be used to do the job properly
choosing, using and caring for PPE and RPE
decontamination procedures
waste disposal procedures
emergency procedures
any other legal requirements (for example, contaminated sites).
If the worker is required to hold other licences for the particular task, for example a demolition licence, additional training may be provided to cover this type of work.
The licensed asbestos removalist must keep a record of all training undertaken by a worker who is carrying out licensed asbestos removal work:
while the worker is carrying out licensed asbestos removal work
for five years after the day the worker stopped carrying out licensed asbestos removal work for the removalist.
The training record must be readily accessible at the asbestos removal area and available for inspection under the WHS Act.
3.3 Informing parties of the licensed asbestos removal
Prior to any licensed asbestos removal work being carried out at a workplace, the licensed asbestos removalist must inform the person with management or control of the workplace about the work and the date it is to commence.
The person with management or control of the workplace must then ensure the following persons are told that the asbestos removal work is to be carried out and when the work is to commence:
the person’s workers and any other persons at the workplace
the person who commissioned the asbestos removal work
anyone conducting a business or undertaking at or in the vicinity of the workplace
anyone occupying premises in the immediate vicinity of the workplace.
If the workplace is a domestic premises, the licensed asbestos removalist must, so far as is reasonably practicable, before commencing the licensed asbestos removal work tell the following people about the asbestos removal work and when it will commence:
the person who commissioned the asbestos removal work
a person conducting a business or undertaking at the workplace
the occupier of the domestic premises
the owner of the domestic premises
anyone occupying premises in the immediate vicinity of the workplace.
Providing information to persons that may carry out licensed asbestos work
A licensed asbestos removalist must provide the following information to a person who is likely to be engaged to carry out the work:
the health risks and health effects associated with exposure to asbestos
the need for and details of health monitoring of a worker carrying out licensed asbestos removal work. Section 1.4 of this Code provides more specific details on health monitoring.
3.4 Obtaining the asbestos register
Before commencing the licensed asbestos removal work, the licensed asbestos removalist must obtain a copy of the asbestos register for the workplace from the person with management or control of the workplace.
This provision does not apply if the work is being carried out at a domestic premise.
3.5 Preparing an asbestos removal control plan
A licensed asbestos removalist must prepare an asbestos removal control plan for any licensed asbestos removal work they are commissioned to undertake.
What is the purpose of an asbestos removal control plan?
An asbestos removal control plan is a document that identifies the specific control measures a licence holder will use to ensure workers and other persons are not at risk when asbestos removal work is being conducted. It is similar to a job safety analysis (JSA) but is focused on the specific control measures necessary to minimise any risk from exposure to asbestos.
An asbestos removal control plan helps ensure the asbestos removal is well planned and carried out in a safe manner. An asbestos removal control plan is only required to be prepared for licensed asbestos removal work. However, one can be prepared to assist when planning asbestos removal work that does not require a licence.
The licensed asbestos removalist must also take into account any asbestos register relevant to the asbestos to be removed and the area to be worked on. The structure of the asbestos removal control plan may be generic but each plan must address the specific situation requirements for each job.
When is an asbestos control removal plan required to be prepared?
The asbestos removal control plan must be prepared before the licensed asbestos removal work commences.
What is contained in an asbestos removal control plan?
The asbestos removal control plan must include details of:
how the asbestos removal will be carried out, including the method, tools, equipment and PPE to be used
the asbestos to be removed, including the location, type and condition of the asbestos.
Specifications or drawings that are relevant to the asbestos removal can also be attached to the asbestos removal control plan to provide additional information about the asbestos. Appendix A provides further detail of what can be in a comprehensive asbestos removal control plan.
Preparing the asbestos removal control plan
When preparing the asbestos removal control plan, the licensed asbestos removalist should consult with the person who commissioned the work, the person with management or control of the workplace (if not the same person), workers and their health and safety representatives.
For the same reasons, if licensed asbestos removal work is being carried out at domestic premises, the licensed asbestos removalist should consult with the person who commissioned the removal work, the owner or the occupier (if not the same person).
Access to the asbestos removal control plan
Once the asbestos removal control plan is prepared, a copy must be:
given to the person who commissioned the licensed asbestos removal work
readily accessible on-site for the duration of the licensed asbestos removal work to:
oa person conducting a business or undertaking at the workplace
oworkers and their health and safety representatives
othe occupants of the premises (if domestic premises).
The asbestos removal control plan must also be made available for inspection under the WHS Act.
3.6 Notifying the regulator of the licensed asbestos removal work
A licensed asbestos removalist must notify the regulator in writing at least five days before the licensed asbestos removal work commences.
The following information must be included in the notification:
name, registered business name, Australian Business Number, licence number and business contact details of the licensed asbestos removalist
name and business contact details of the supervisor who will oversee the removal work
name of the licensed assessor or competent person engaged to undertake air monitoring and to issue the clearance certificate
client name and contact details
name, including registered business or corporate name, of the person with management or control of the workplace
address of the workplace, including the specific location if it is a large workplace
kind of workplace where the removal work will be performed (for example, whether it is an office building or construction site and the type of work that is carried out there, if any)
date of notification
the start date of the removal work and an estimation of how long it will take
whether the asbestos to be removed is friable or non-friable
the type of the asbestos (for example, asbestos-contaminated sheeting, vinyl tiles, lagging, gaskets)
if the asbestos is friable, the way the removal area will be enclosed
estimated quantity of asbestos to be removed
number of workers who will perform the removal work and details of their competency to carry out removal work.
It may not be possible to provide five days notice, and removal work may commence immediately in the following limited circumstances:
a sudden expected event that may lead to a situation where there is a risk of exposure, for example a burst pipe that was lagged with asbestos or a forklift crashing into an asbestos cement sheet wall
an unexpected breakdown of an essential service that requires immediate rectification, for example gas, water, sewerage or telecommunications services.
If this is the case, the licensed asbestos removalist must notify the regulator immediately by telephone and in writing within 24 hours after the notice provided over the telephone.
3.7 Limiting access, displaying signs and installing barricades
A person who is carrying out licensed asbestos removal work must ensure that signs indicate where the asbestos removal work is being carried out and barricades are erected to delineate the asbestos area. This will assist in limiting access to the asbestos removal work area.
If the person who commissions the licensed asbestos removal work and the person with management or control of the workplace (if not the same person) is aware that licensed asbestos removal work is being carried out, they must ensure that access to the removal area is limited to the following people:
workers who are engaged to carry out the removal work
other people who are associated with the removal work
people who are allowed under the WHS Regulations or another law to be in the asbestos removal area (for example, inspector, emergency service workers).
A combination of using signs and barricades may be necessary to limit access to the asbestos removal area, for example installing a fence and signs may be used as a method to inform people that it is the asbestos removal area. Using locking access doors may be appropriate as long it does not create an evacuation hazard.
All people who have access to the removal area should comply with any direction given by the licensed asbestos removalist.
Section 4.2 of this Code provides further detail on the type of signs and barricades that should be used at a workplace.
3.8 Decontamination
When carrying out licensed asbestos removal work, the licensed asbestos removalist must ensure decontamination facilities are available for the asbestos removal work area, any plant used in that area and workers carrying out the asbestos removal work.
Section 4.6 of this Code outlines decontamination procedures that can be put in place at the workplace.
3.9 Waste containment and disposal
When carrying out licensed asbestos removal work, the licensed asbestos removalist must ensure that asbestos waste is contained and labelled in accordance with the GHS before the waste is removed from the asbestos removal area. It must be disposed of as soon as is practicable at a site authorised to accept asbestos waste.
PPE
Disposable PPE that has been used in the asbestos work area and is contaminated with asbestos must be sealed and labelled in a container and disposed of upon completion of the asbestos removal work.
In some cases, it may not be reasonably practicable to dispose of PPE that is clothing. In this case, the clothing must be laundered at a laundry that is equipped to launder asbestos-contaminated clothing. If this cannot be done, the clothing must be sealed in a container until is reused for asbestos removal purposes.
It may also not be reasonably practicable to dispose of PPE that is not clothing. If this is the case, the clothing must be decontaminated prior to it being removed from the asbestos removal area. If this cannot be done, the PPE must be sealed in a container until it is reused for asbestos removal purposes.
Where a sealed container has been used, it must be decontaminated and labelled in accordance with the GHS prior to it being removed from the asbestos removal area to indicate that it contains asbestos.
Section 4.5 of this Code provides guidance on the type of PPE that can be used. Section 4.8 of this Code outlines waste containment and disposal procedures that can be implemented at the workplace.
3.10 Clearance inspection
A person commissioning licensed asbestos removal work must ensure that, once the licensed asbestos removal work has been completed, a clearance inspection is carried out and a clearance certificate is issued before the workplace can be re-occupied by:
an independent licensed asbestos assessor, for work that must be carried out by a Class A licensed asbestos removalist (for example, if the removal work involved friable asbestos)
an independent competent person, for asbestos work that is not required to be carried out by a Class A licensed asbestos removalist (for example, if removal work involved more than 10 m² of non-friable asbestos).
This also includes where the work is being carried out at domestic premises.
To be independent, the licensed asbestos assessor or competent person must not be involved in the removal of asbestos for that specific job and is not involved in a business or undertaking involved in the removal of the asbestos for that specific job.
In some cases, it may not be reasonably practicable for the licensed asbestos assessor or competent person to be independent from the person who carried out the asbestos removal work. If this is the case, the person commissioning the work can apply to the regulator for an exemption from this requirement under Part 11.2 of the WHS Regulations.
The independent licensed assessor or competent person must not issue a clearance certificate unless they are satisfied that the asbestos removal area and the area immediately surrounding it are free from visible asbestos contamination. To do this, they can conduct a visual inspection for evidence of dust and debris. If air monitoring was also conducted, the results of that test must show that asbestos is below 0.01 fibres/ml.
If a clearance certificate has not been obtained, the asbestos removal area must not be re‑occupied for normal use or other work activities. A clearance certificate must be issued before the area can be re-occupied for demolition or other work.
Unauthorised persons cannot enter the asbestos removal work area prior to a clearance certificate being issued and any protective barricades should remain in place until the completion of all licensed asbestos removal work and the final clearance certificate is issued.
Appendix C provides an example of a clearance certificate.
3.11 Air monitoring
Air monitoring involves sampling airborne asbestos fibres to assist in assessing exposure to asbestos and the effectiveness of implemented control measures. It must be conducted in accordance with the Guidance Note on the Membrane Filter Method for Estimating Airborne Asbestos Dust, 2nd Edition [NOHSC: 3003 (2005)].
When is air monitoring required?
Air monitoring requirements will vary depending on the type of asbestos being removed, the location and position of the asbestos, if an enclosure is used and whether the asbestos removal work is within a building or outside.
Friable asbestos removal – Air monitoring is mandatory for all friable asbestos removal. This includes prior to dismantling an enclosure and for the purposes of the clearance inspection.
More than 10 m² of non-friable asbestos removal – Air monitoring is not required but may be considered to be carried out by an independent licensed asbestos assessor or competent person to ensure compliance with the duty to eliminate or minimise exposure to airborne asbestos and to ensure the exposure standard is not exceeded.
Public Location – Air monitoring should be considered where the asbestos removal work is being undertaken in or next to a public location.
Exposure air monitoring – Air monitoring should be carried out at other times to determine a worker’s exposure to airborne asbestos if, based on reasonable grounds, there is uncertainty as to whether the exposure standard may be exceeded and a risk assessment by a competent person indicates it is necessary. Since most uses of asbestos are prohibited, exposure monitoring should not be required frequently.
Air monitoring may be required when:
it is not clear whether new or existing control measures are effective
there is evidence (for example, dust deposits are outside the enclosure) the control measures have deteriorated as a result of poor maintenance
modifications or changes in safe work methods have occurred that may adversely affect worker exposure
there has been an uncontrolled disturbance of asbestos at the workplace.
When must the air monitoring be carried out?
The air monitoring must be conducted before and during Class A asbestos removal work. However, it is not required before friable asbestos removal work commences when the glove bag removal technique is used. Air monitoring must be carried out as part of the clearance inspection, for instance at the conclusion of the asbestos removal work.
Who must conduct air monitoring?
A person who commissions asbestos removal work that requires a Class A licence must ensure that an independent licensed asbestos assessor undertakes air monitoring of the asbestos removal area at the workplace.
In relation to asbestos removal work requiring a licence:
Friable asbestos removal – An independent licensed asbestos assessor must be engaged to carry out air monitoring when it is required.
Non-friable asbestos removal (more than 10 m²) – An independent licensed asbestos assessor or competent person must be engaged to carry out air monitoring when it is required.
Where air monitoring is otherwise required, for instance to determine whether the exposure standard has been exceeded following an uncontrolled disturbance or release of asbestos at the workplace, an independent licensed asbestos assessor or competent person may carry it out. However, if the release involves friable asbestos, only an independent licensed asbestos assessor can carry out the air monitoring.
Results of the air monitoring
Once the results of the air monitoring are received, the licensed asbestos removalist must take action depending on the respirable fibre level. Where the results show that respirable asbestos fibre levels exceed the action levels outlined in Table 1, action must be taken immediately.
Table 1 Air monitoring action levels
| Action level | Control | Action |
| Less than 0.01 fibres/ml | No new control measures are necessary | Continue with control measures |
| At 0.01 fibres/ml or more than 0.01 fibres/ml but less than or equal to 0.02 fibres/ml | 1. Review | Review control measures |
| 2. Investigate | Investigate the cause | |
| 3. Implement | Implement controls to eliminate or minimise exposure and prevent further release | |
| More than 0.02 fibres/ml | 1. Stop removal work | Stop removal work |
| 2. Notify regulator | Notify the relevant regulator by phone followed by fax or written statement that work has ceased and the results of the air monitoring | |
| 3. Investigate the cause | Conduct a thorough visual inspection of the enclosure (if used) and associated equipment in consultation with all workers involved with the removal work | |
| 4. Implement controls to eliminate or minimise exposure and prevent further release | Extend the isolated/barricaded area around the removal area/enclosure as far as reasonably practicable (until fibre levels are at or below 0.01 fibres/ml, wet wipe and vacuum the surrounding area, seal any identified leaks (e.g. with expandable foam or tape) and smoke test the enclosure until it is satisfactorily sealed. | |
| 5. Do not recommence removal work until further air monitoring is conducted | · Do not recommence until fibre levels are at or below 0.01 fibres/ml |
Any information that is gathered from these actions can be referred to during future asbestos removal jobs (where applicable).
Communicating the results of the air monitoring
The person who commissions the licensed asbestos removal work must ensure the results of the air monitoring are given to the following persons:
workers at the workplace
health and safety representatives for the workplace
persons conducting businesses or undertakings at the workplace
other persons at the workplace.
If the workplace is domestic premises, the licensed asbestos removalist must ensure the results are given to the following persons:
the person who commissioned the work
workers at the workplace
health and safety representatives for the workplace
persons conducting businesses or undertakings at the workplace
the occupier of the domestic premises
the owner of the domestic premises
other persons at the workplace.
3.12 Removing friable asbestos
When a licensed asbestos removalist is removing friable asbestos (requiring a Class A licence), the following must occur, so far as is reasonably practicable:
the asbestos removal area is enclosed to prevent the release of respirable asbestos fibres
negative pressure is used, provided the enclosure being used has been tested for leaks
the wet method of asbestos removal is used
the asbestos removal work area does not commence until the air monitoring is started by an independent licensed asbestos assessor, provided the enclosure has been tested for leaks
air monitoring is undertaken during the asbestos removal work at times decided by the independent licensed assessor undertaking the monitoring
any glove bag used to enclose the asbestos removal area is dismantled and disposed of safely.
However, if the glove bag method is used, negative pressure and conducting air monitoring prior to the work commencing are not required.
The enclosure must not be dismantled until the results are received from:
if the friable asbestos is removed from a domestic premises – the licensed asbestos assessor who undertook the air monitoring
in any other case – the person who commissioned the Class A asbestos removal work.
The results must show that the respirable asbestos fibre level is below 0.01 fibres/ml.
The enclosure must be decontaminated prior to dismantling it to minimise, so far as is reasonably practicable, the release of respirable asbestos fibres. The person who commissions the removal of the friable asbestos must obtain a clearance certificate from the licensed asbestos assessor after the enclosure has been dismantled.
Chapter 6 provides further detail on enclosures. Section 4.3 provides further detail on the wet method. Section 7.2 provides further detail on the glove bag method.
CONTROLS APPLICABLE TO ALL TYPES OF ASBESTOS REMOVAL
Note: This chapter applies to all asbestos removal work i.e. Class A and Class B licensed asbestos removal work and asbestos removal work that does not require a licence.
4.1 Identifying hazards
An asbestos removalist should consider not only the direct hazards that are associated with the asbestos removal work but also those hazards related to the work activity and the work environment (for example, demolition or construction).
Confined spaces
Removing asbestos in a confined space should only be undertaken where it is not possible to avoid doing work in that space. A safe system of work should be developed for inclusion in the asbestos management plan or asbestos removal control plan.
Friable asbestos removal requires the use of enclosures that are designed to eliminate or minimise the release of airborne asbestos spreading from the asbestos removal work area. Depending on the conditions inside the enclosure, an asbestos enclosure may also become a confined space.
Further information is available in the Code of Practice: Confined Spaces.
Falls
Work at heights should not be undertaken if the task can be performed on the ground. If asbestos removal work must be undertaken at height, then the WHS Regulations apply. Further information is available in the Code of Practice: How to Prevent Falls at Workplaces.
Heat stress
Heat-related hazards can be created from working in enclosures or confined spaces or using PPE. The factors that can lead to heat stress should be considered, including temperature, humidity, air movement, exposure to a heat source, work activities and demands, how long the PPE must be worn and individual physical factors.
Control measures include:
selection of appropriate PPE fitted to reduce the build-up of heat
adequate number of extraction units in enclosures
cool cotton underclothing
scheduling appropriate work breaks
job rotation
cool drinks readily available
providing a cool, shaded rest area
educating workers about heat stress risks and controls.
Further information is available in the Code of Practice: Managing the Work Environment and Facilities.
Electrical equipment
When undertaking asbestos removal work, the risk associated with electrical equipment should be controlled by following the procedures set out below.
De-energisation and removal from the asbestos removal work area. If the electrical equipment cannot be disconnected and removed they must be de-energised. The de-energised equipment must be secured so it cannot be inadvertently re-energised.
Any electrical cabling or equipment remaining in the asbestos removal area must be labelled and protected from mechanical damage or the ingress of water in accordance with AS/NZ3000:2000 Wiring rules.
A licensed electrician must safely remove and reinstall electrical cables and equipment.
For electrical equipment such as fire detectors, smoke detectors and thermal detectors, only a person able to remove and isolate the circuits and heads as required prior to the asbestos removal work should be engaged to do that.
Upon completion of the asbestos removal work, a person should replace, reactivate and test the system, prepare a certificate stating that the heads are operational and forward to the asbestos removalist.
All portable electrical tools and equipment, including flexible leads and any electrical installations utilised by workers during asbestos removal, should comply with AS/NZS 3012:2003 Electrical installations – construction and demolition sites.
Further information is available in the Code of Practice: Managing Risks with Electrical Work.
4.2 Indicating the asbestos removal areas
The asbestos removalist must use signs and barricades to clearly indicate the area where the asbestos removal work is being performed. Signs must be placed in positions so that people are aware of where the asbestos removal work area is and should remain in place until removal is completed and clearance to reoccupy has been granted. Responsibilities for the security and safety of the asbestos removal site and removal work area should be specified in the asbestos removal control plan (where required). This includes inaccessible areas that are likely to contain asbestos.
Warning signs
Warning signs must be placed so they inform all people nearby that asbestos removal work is taking place in the area. Signs should be placed at all of the main entry points to the asbestos removal work area where asbestos is present.
These signs should be weatherproof, constructed of light-weight material and adequately secured so they remain in prominent locations. The signs should be in accordance with AS 1319-1994 Safety signs for the occupational environment for size, illumination, location and maintenance.
Barricades
The use of barricades assists with traffic control and prevents access to the asbestos removal site and removal work area.
The purpose of barricades is to delineate and isolate the asbestos removal area with appropriately placed barricades. Barricades can take various forms, from tape to solid hoarding. The type of barricading should reflect the level of risk. For friable asbestos removal work, solid barricades should be used. Tape may be appropriate for non-friable asbestos removal work of short duration.
The location of barricades will depend on the physical environment and the level of risk.
An assessment of the asbestos removal work site should determine the appropriate placement
of barricades.
For example, a non-friable asbestos cement removal job where the asbestos cement is in good condition may use a wall located three metres from the asbestos removal area as the barrier.
A friable sprayed asbestos removal job being performed dry due to electrical restrictions may require a barricade 15 metres from the asbestos removal area.
In determining the distance between barriers and the asbestos removal area, the following should be considered:
whether the asbestos is friable or non-friable
activity around the asbestos removal area (for example, other workers, visitors, neighbours, the public) to determine the risk of exposure to other people
the method of asbestos removal
any existing barriers (walls, doors)
the quantity of asbestos to be removed
the type of barrier used (for example, hoarding or tape).
4.3 Wet and dry methods
An asbestos removalist must use techniques to eliminate or minimise the generation of asbestos fibres so far as is reasonably practicable. They must choose the method of asbestos removal that is most effective at minimising fibre release at the source. The removal methods are listed in preferred order:
Wet spray method - asbestos fibres are significantly suppressed; however, they are not entirely eliminated so the use of RPE is as essential.
Saturation and water injection method – used during friable removal.
Dry method - can only be used if the wet spray method is not suitable, for example if there are live electrical conductors or if equipment could be permanently damaged or made dangerous by contact with water.
Wet spray method
The wet spray method is the preferred asbestos removal method and should be used for the removal of asbestos from structures and plant. The wet spray method requires the use of a constant low-pressure water supply for wetting down asbestos and related items to suppress asbestos fibres. This can be achieved with a mains-supplied garden hose fitted with a pistol grip.
If no water supply is readily available, a portable pressurised vessel (for example, a pump-up garden sprayer) may be used.
The design of the spraying equipment will depend on the availability of a water supply and access to the area to be sprayed.
The wet spray method involves applying a fine water spray to the asbestos in a manner that ensures the entire surface of the asbestos is saturated and the run-off is minimised. The asbestos should be maintained in a wet condition throughout the removal.
A wetting agent (surfactant), for example detergent, may be added to the water to facilitate more rapid wetting of the asbestos.
A manually controlled, consistent low-pressure, fine spray (for example, from an adjustable pistol-grip garden hose) is recommended.
For very small areas, a small spray water bottle may be sufficient. In all cases, the use of water should be in the form of a mist to minimise the potential to generate respirable dust.
The asbestos should be wetted through to its full depth and the water spray should be directed at the site of the cut. The wetted material should be removed as the cut is progressed.
Immediately after the asbestos is removed from its fixed or installed position, spray should be directed on sides previously not exposed.
The wet friable asbestos removed in sections should immediately be placed in suitably labelled asbestos waste containers and properly sealed along with any small sections dislodged as the asbestos is cut.
Wherever reasonably practicable, a HEPA-fitted vacuum cleaner should be used in conjunction with the wet spray method. The HEPA vacuum cleaner should be used prior to spraying asbestos with water and for the collection of any dust spread over a large area.
Airborne asbestos fibres are significantly suppressed when the wet spray method is used; however, they are not entirely eliminated so effective PPE including RPE is also essential. Refer to Section 4.5 of this Code for information on RPE.
Consideration should be given to applying a PVA emulsion as it may be more effective than water (with a wetting agent) in minimising fibre release. For example, PVA can be applied and allowed to dry on AC roofing prior to its removal as an alternative method to prevent slip hazards.
Saturation and water injection method
The soaking method with total saturation should be used if the asbestos is so thick that the spray method will not suppress the asbestos significantly. This method involves injecting water or a water-based solution directly into friable asbestos. It is a process that requires specific training in relation to the use of the equipment and the process.
The asbestos is soaked by the introduction of water or other wetting agents through an appropriate applicator that consists of an injection head with numerous side holes or outlets through which the water or wetting agent is fed to the asbestos.
To facilitate more rapid wetting of the asbestos, holes or cuts should be made in the outer covering to enable the water or wetting agent to be injected in such a manner as to ensure that the asbestos is saturated but not just washed out through a liquid passage.
The soaking should be done before removal. The quantity of water or wetting agent and the time to soak will depend on the thickness of the asbestos, access to the asbestos and location of the holes.
The saturated asbestos should then be removed in sections, placed in a properly labelled container, sealed and disposed of as with the spray method.
Dry method
The dry method is not preferred as there is a much greater potential for airborne asbestos fibres to be generated. The dry removal method can only be used if the wet spray or soaking methods are not suitable, for example if there are live electrical conductors or if major electrical equipment could be permanently damaged or made dangerous by contact with water.
If the dry removal method is used, the following controls should be implemented:
Non-friable removal – Enclose the asbestos removal work area as far as is reasonably practicable.
Friable removal – Fully enclose the asbestos removal work area with plastic sheeting (a minimum 200 µm thick) and maintain at a negative pressure (at least 12 Pa water gauge). Ensure all workers involved in the removal operation wear full-face positive-pressure supplied air-line respirators.
Friable and non-friable removal – The asbestos should be removed in small, pre-cut sections with minimal disturbance to minimise the generation of airborne asbestos fibres as much as possible. Wherever reasonably practicable, a HEPA-fitted vacuum cleaner should be used.
All waste material should be immediately placed in appropriate wet containers which are wetting to suppress creation of dust and airborne fibres.
4.4 Tools and equipment
Tools and equipment that can be used during asbestos removal work include asbestos vacuum cleaners, manually operated hand tools and equipment—other than compressed air or high pressure water spray—that have been designed to capture or suppress respirable dust or are used in a way that is designed to capture or suppress respirable dust.
In addition to any equipment required to complete a particular task, the following equipment may be required on-site before the work begins:
disposable cleaning rags
bucket of water and/or a misting spray bottle
sealant
suitable asbestos waste container
warning signs and/or barrier tape.
Prohibited tools and equipment
Tools and equipment that generate dust must not be used on asbestos. These include:
high-speed abrasive power and pneumatic tools, for example angle grinders, sanders, saws and high-speed drills
brooms and brushes (unless brushes are used for sealing)
high-pressure water spray, jets, power or similar tools and instruments on asbestos in the workplace
compressed air.
The use of tools and equipment that cause the release of asbestos, including power tools and brooms, may be used on asbestos if the equipment is enclosed and/or designed to capture or suppress asbestos fibres and/or the equipment is used in a way that is designed to capture or suppress asbestos fibres safely, for example:
enclosing the tool or instrument
engineering controls such as extraction ventilation
using the tools and instruments within an enclosed removal area (for example, full enclosure or small enclosure).
Controls are assumed to be effective if exposure monitoring results are less than 0.05 f/ml or control monitoring results are less than 0.01 f/ml. Should either of these values be exceeded during monitoring, work must cease and the control measures that are in place reviewed or improved to ensure the levels of airborne asbestos do not exceed these levels.
Inspection and maintenance of equipment
After the asbestos removal work is completed, tools must be decontaminated (refer to Section 4.6).
All equipment used for the removal of asbestos should be inspected before the commencement
of the asbestos removal work, after any repairs and at least once every seven days when it is continually being used. A register with the details of these inspections, the state of the equipment and any repair details should be maintained.
Asbestos vacuum cleaners
Asbestos vacuum cleaners should comply with the Class H requirements in Australian Standard AS/NZS 60335.2.69 Industrial vacuum cleaners or its equivalent. Asbestos vacuum cleaners should not be used on wet materials or surfaces. Attachments with brushes should not be used
as they are difficult to decontaminate.
Filters for these vacuum cleaners should conform to the requirements of AS 4260-1997 High efficiency particulate air (HEPA) filters – Classification, construction and performance or its equivalent.
Household vacuum cleaners must never be used where asbestos is or may be present, even if they have a HEPA filter.
Asbestos vacuum cleaners can only be used for collecting small pieces of asbestos dust and debris. Larger pieces should be picked up and placed in suitable waste containers and should never be broken into smaller sizes for vacuuming.
The asbestos removalist should ensure that procedures are established for the general maintenance, including emptying, of asbestos vacuum cleaners in a controlled environment.
They should be cleaned externally with a wet cloth after each task, the hose and attachments should be stored in a labelled impervious bag, and a cap should be placed over the opening to the asbestos vacuum cleaner when the attachments are removed.
PPE should be worn whenever an asbestos vacuum cleaner is opened to change the bag or filter or to perform other maintenance.
The emptying of asbestos vacuum cleaners can be hazardous if the correct procedures are not followed. Asbestos vacuum cleaners should only be emptied by a competent person with the correct PPE, in a controlled environment and in compliance with the manufacturer’s instructions.
Whenever possible, asbestos vacuum cleaners should not be hired, as they can be difficult to fully decontaminate.
Hiring may be more viable in some instances if they are completely decontaminated, such as when a one-off maintenance task is required for asbestos. Asbestos vacuum cleaners should be hired only from organisations that provide vacuum cleaners specifically for work involving asbestos and the asbestos vacuum cleaner has been previously decontaminated. If hired, the asbestos vacuum cleaner should be decontaminated before it is returned.
Alternatively, the hire organisation may undertake the decontamination and maintenance of the filters and bags of the asbestos vacuum cleaner itself. In these cases, the asbestos vacuum cleaner should be hired out in a sealed storage container, with instructions that it may be removed from the container only when it is inside the asbestos removal work area and users are wearing appropriate PPE. When the minor maintenance work is completed the asbestos vacuum cleaner should be resealed in the storage container provided, and the sealed storage container should then be decontaminated by wet wiping before it is removed from the asbestos removal work area and returned to the hire organisation for decontamination and maintenance.
Organisations that hire out asbestos vacuum cleaners should ensure all their asbestos vacuum cleaners are decontaminated, maintained in good working order and the hirers are competent in their safe use. It is suggested that asbestos vacuum cleaners are only hired out to asbestos removal supervisors or licence holders.
At the completion of the asbestos removal work, the tools and equipment must be decontaminated, placed in sealed, labelled containers and if necessary, disposed of as asbestos waste. The asbestos vacuum cleaner and attachments must also be decontaminated. The bag and filter must be removed in accordance with the manufacturer’s instructions and disposed of as asbestos waste.
Spray equipment
Spray equipment includes wet sprays with water mist or wetting solution. A constant low-pressure water supply is required for wetting down asbestos and related items to suppress airborne asbestos fibres.
Wet spray can be achieved with a mains-supplied garden hose fitted with a pistol grip. If no water supply is readily available, a portable pressurised vessel (such as a pump-up garden sprayer) may be used. For very small areas, a small spray water bottle may be sufficient. In all cases, the use of water should be in the form of a mist to minimise the potential to generate airborne dust.
4.5 Personal protective equipment
An asbestos removalist must provide all workers with PPE that is suitable for asbestos removal work. Workers must also use the PPE given to them by the asbestos removalists. PPE must be worn at all times during the work in the asbestos removal area. PPE includes clothing, for example coveralls, gloves and safety footwear, as well as RPE. The appropriate PPE can be determined by conducting a risk assessment.
Personal protective clothing should be made from materials that provide protection against fibre penetration and not from wool or other materials that attract fibrous dusts.
All equipment used for the removal of asbestos should be inspected before the commencement of the asbestos removal work, after any repairs and at least once every seven days when it is continually being used. A register with the details of these inspections, the state of the equipment and any repair details should be maintained.
At the end of the asbestos removal work and upon leaving the asbestos removal work area, all PPE must be disposed of as asbestos waste or decontaminated and stored in sealed double bags before being removed from the asbestos removal site to be laundered by a laundry with facilities for laundering asbestos-contaminated materials. PPE should be thoroughly wet before being placed in bags.
Coveralls
Disposable coveralls should be provided wherever reasonably practicable and should be:
of a suitable standard to prevent tearing or penetration of asbestos fibres so far as is practicable. Disposable coveralls rated type 5, category 3 (prEN ISO 13982–1) or equivalent would meet this standard
one size too big, as this will help prevent ripping at the seams
fitted with hood and cuffs, ensuring that:
oif cuffs are loose, they are sealed with tape
ocoverall legs are worn over footwear as tucking them in lets the dust in
othe fitted hood is worn over the respirator straps.
Coveralls should:
not be made of material that is easily torn or have external pockets or velcro fastenings because these are easily contaminated and difficult to decontaminate
never be taken home
never be reused
be disposed of as asbestos waste after a single use.
If it is not reasonably practicable to provide coveralls that can be disposed of after a single use, the coveralls may be laundered at a commercial laundry equipped to launder asbestos-contaminated clothing by prior arrangement. The coveralls must be sealed in a decontaminated container before they are removed from the asbestos removal work area. However, laundering of asbestos-contaminated protective clothing is not recommended because decontamination cannot be guaranteed. It is recommended that such re-usable coveralls should only be used in limited instances, for example in emergency services where the coveralls must be inflammable to protect against fire hazards and continual disposal and replacement is not practicable. Refer to Section 4.8 for more information on laundering of contaminated clothing.
In some cases (particularly dusty jobs) double coveralls should be used, with the outer coverall being removed a predetermined distance from the final decontamination area. Disposable coveralls should be wrapped in a double layer of plastic before disposal as asbestos-contaminated waste after the removal task is completed.
Gloves
If significant quantities of asbestos fibres may be present, single-use disposable gloves should be worn. If latex gloves must be used, low protein (powder free) gloves should be used. If latex gloves are not available, disposable nitrile gloves can be used as an alternative.
Gloves used for asbestos removal work should be disposed of as asbestos waste and the workers should clean their hands and fingernails thoroughly whenever leaving the asbestos removal work area. However, as with coveralls, if it is not reasonably practicable to use disposable gloves, they may be laundered appropriately in limited circumstances.
Footwear
Safety footwear (for example, steel-capped, rubber-soled work shoes or gumboots) should be provided for all workers removing asbestos. Footwear should be laceless, as laces and eyelets can be contaminated and are difficult to clean. It should remain inside the barricaded area or dirty decontamination area for the duration of the asbestos removal work and should not be shared for hygiene reasons. Disposable overshoes should be avoided unless they are of a design that has an anti-slip sole.
When safety footwear is not in use, it should be stored upside down to minimise asbestos contamination inside the footwear. Storage facilities should be provided to allow for storage of the shoes. At the end of the removal work and each time the worker leaves the asbestos removal work area, safety footwear must be:
decontaminated
sealed in double bags for use on the next asbestos removal site (but not for any other type
of work)disposed as asbestos waste.
Respiratory protective equipment (RPE)
All workers engaged in asbestos removal work must wear RPE conforming to the requirements
of AS/NZS 1716:2012 Respiratory Protection Devices or its equivalent.
The level of respiratory protection and supplied air respirators should be determined by a competent person. The selection of suitable RPE depends on the nature of the asbestos removal work, the probable maximum concentrations of asbestos fibres expected and any personal characteristics of the wearer that may affect the facial fit of the respirator (for example, facial hair and glasses).
Disposable RPE is not preferred, however if selected, it should be stored in a suitable and clean location before use and disposed of after a single use.
A competent person may change the level of RPE at any stage during the asbestos removal job following an assessment of the asbestos fibre levels experienced inside the asbestos removal work area. For example, this may occur during the final clean-up after the removal of friable asbestos when the use of air-lines is no longer considered necessary.
If a medical condition precludes the use of negative pressure respirators, workers should be provided with a continuous-flow, positive pressure respirator wherever possible.
At every asbestos removal job, the workers should be reinstructed in the necessity to wear RPE correctly to guard against complacency.
A fit test should be performed to ensure the RPE fits the individual and provides a good face seal between the worker’s skin and the face piece. Fit tests should be repeated when changing from different models of RPE or a different sized face piece.
Appendix B provides more information on selecting suitable RPE and fit tests.
Using and maintaining RPE
RPE must be worn at all times in the asbestos removal area and until the appropriate stage of personal decontamination.
Asbestos removalists or asbestos removal supervisors must ensure all workers undertaking any asbestos removal work receive instruction and training in:
fit testing/checking
the importance of a correct facial fit
the correct method of using their respirators
the procedures for regular cleaning, inspection and maintenance of respirators before use
when to stop asbestos removal work and leave the area if they think their RPE is not working properly.
The respirator must be worn in accordance with the manufacturer’s instructions and the coverall hood must go over the respirator straps. It should be examined in accordance with the manufacturer’s instructions before use to ensure that it is not damaged and is in good working order. Respirator defects should be reported immediately to the asbestos removal supervisor.
The pre-use examination should include an inspection of:
the condition of the straps and face piece, including the seal and the nose piece
Fit testing of face pieces
The fit of a negative-pressure respirator to a worker’s face is critical. A fit test, in accordance with AS/NZS 1715:2009 Selection, Use and Maintenance of Respiratory Protective Devices and the manufacturer’s instructions, should be performed to assist in determining the best fit respirator for the individual worker immediately before commencing work and a fit check performed each time the respirator is to be used.
The performance of RPE depends on a good contact between the wearer’s skin and the face seal of the mask so that the mask is a tight-fitting face piece or full mask. A good face seal can only be achieved if the wearer is clean-shaven in the region of the seal and the face piece is the correct size and shape to fit the wearer’s face.
Workers using negative-pressure respirators should also be clean-shaven to ensure a good face seal. Workers with beards, stubble or facial hair should use a continuous-flow positive pressure respirator.
Workers wearing prescription glasses with side arms may not be able to use full-face respirators because of the loss of seal around the spectacle arms. If their glasses cannot be modified so they do not need the support of the ears, these workers should not use full-face respirators and should wear air supply hoods instead. Ensure that these hoods will provide a sufficient level of protection.
Where the half-face respirator has been selected as providing the most appropriate protection and a seal or fit is not achievable from non-disposable respirators, a disposable respirator may be used.
To conduct a full- or half-face respirator fit check:
close off inlet to filter
inhale gently
hold for 10 seconds
check that the face piece remains slightly collapsed, as it should.
APPENDIX C – EXAMPLE OF A CLEARANCE CERTIFICATE
SECTION A – CLEARANCE INSPECTION DETAILS
Note: Where asbestos removal work requires a Class A licence, an independent licensed asbestos assessor must carry out the clearance inspection and complete a clearance certificate if satisfied that the area is safe to reoccupy.
| Client details | |
Name of client: | |
Client contact details: | |
| Removal work details | |
Date removal work carried out: | |
| Site address where removal work is being carried out: | |
| Details of the specific asbestos removal work area(s): | |
| Name of licensed asbestos removalist: | |
| Name and contact details of licensed asbestos removalist supervisor (if different to removalist): | |
| Inspection details | |
Date of clearance inspection: | |
Time of clearance inspection: | |
SECTION B – ASBESTOS REMOVAL WORK PAPERWORK
| Yes | No |
| Do you have a copy of the asbestos removal control plan ? | |
| Do you have a copy of the notification form? | |
| Is the removal work consistent with the control plan and the notification form? (e.g. use of enclosures, decontamination facilities, waste facilities) |
SECTION C – ASBESTOS REMOVAL WORK AREA
1. Visual Inspection
| Yes | No |
| Inspection of the specific area detailed in Section A found no visible asbestos remaining as a result of the asbestos removal work carried out. | |
| Is air monitoring required (if no, proceed to Section E) | |
| Can the area be reoccupied? | |
| Has additional information been attached? (e.g. photos, drawings, plans) |
2. Air monitoring
| Yes | No |
| Air monitoring was carried out as part of the clearance inspection. The result was below 0.01 f/ml. | |
| Has the air monitoring sample been analysed by a NATA-accredited laboratory? | |
| Is the air monitoring report attached? | |
| Can the area be reoccupied? |
SECTION D – ENCLOSURES
1. Prior to dismantling the enclosure
| Yes | No |
| The area within the enclosure and the area immediately surrounding the enclosure was inspected and no visible asbestos was found. | |
| Air monitoring was carried out as part of the clearance inspection. The result was below 0.01f/ml. | |
| Is the air monitoring report attached? | |
| Can the enclosure be dismantled? |
Number of samples collected:____________________
| Sample 1 | Sample 2 | Sample 3 | Sample 4 | Sample 5 |
| RESULTS |
2. After the enclosure was dismantled and removed
| Yes | No |
| An inspection of the area in which the enclosure was erected and the area immediately surrounding the area where the enclosure was erected was inspected and no visible asbestos was found. | |
| Air monitoring was carried out as part of the clearance inspection. The result was below 0.01f/ml. | |
| Is the air monitoring report attached? | |
| Can the area be reoccupied? |
Number of samples collected: ____________________
| Sample 1 | Sample 2 | Sample 3 | Sample 4 | Sample 5 |
| RESULTS |
SECTION E – CLEARANCE DECLARATION
I declare that:
the former enclosure, asbestos removal work area and the surrounding area are free from any visible asbestos
the transit route and waste routes are free from any asbestos,
all asbestos in the scope of the removal work has been removed and any known asbestos is intact.
| ........................................................... Signature of licensed asbestos assessor/competent person | ........................................................... Assessor licence number (if applicable) |
| ........................................................... Name of licensed asbestos assessor /competent person |
APPENDIX D – EXAMPLES OF ASBESTOS REMOVAL WORK
This appendix does not address other hazards that may be present at a workplace, for example falls from heights or electrical hazards. These hazards must also be identified and the associated risks controlled.
This appendix provides guidance on how to perform a specific task associated with asbestos removal work. With all tasks, some general requirements include the following:
Obtain the asbestos register prior to commencing asbestos removal work.
Depending on the type of asbestos removal work, follow the requirements outlined in Chapters 2–4 of this Code (for example, laying plastic sheeting, isolating the work areas, signs and barricades, PPE, cleaning up site decontamination).
Asbestos cement products
Asbestos cement products consist of approximately 15 per cent asbestos fibres by weight. A wide range of products have been commonly found—including roofing, shingles, exterior cladding on industrial, public and some domestic premises, corrugated/profile sheets as well as flat sheets—that have been used for exterior flexible building boards.
If possible, you should remove the asbestos cement products whole. If some sections have been damaged prior to removal, these may be strengthened by applying duct tape.
Identify the method in which the asbestos cement product is held in place, then use a method that would minimise airborne dust generation in removing the product. For example:
fasteners: dampen then carefully remove using a chisel
bolts: dampen then use bolt cutters (or an oxy torch) – do not use an angle grinder
screws: dampen then carefully unscrew with a screwdriver
nails: dampen then carefully lever the panel or punch through if absolutely necessary.
Avoid breaking the asbestos cement products. If breakage is absolutely necessary to remove/dislodge the product, dampen the material and minimise breakage.
Remove the asbestos cement product wet/damp by applying a fine water spray, unless this creates an electrical risk.
Once removed from its position, spray the back of the product with a fine water spray. Frequent application of a fine water spray may be required depending on the circumstances (for example,
a very hot day) but be careful not to create a slip hazard.
Personal decontamination must be carried out in accordance with the WHS Regulations and this Code.
Asbestos cement roof sheeting
Asbestos cement can become brittle with age, so any removal work on roofs should address the risk of fall hazards. If lichen is encountered on roof sheeting, caution should be exercised in the use of water and the choice of workers’ footwear because lichen can be slippery, especially when
it is wet.
The removal of asbestos cement roofing must be performed in accordance with the WHS Regulations.
Angle grinders should not be used because of the potential for damage to the asbestos cement and subsequent fibre release. Anchoring screws/bolts should be removed from the roofing sheets using an oxy torch or another suitable device that will not significantly damage the sheet.
If the system of removal involves walking on the roof to remove roof sheeting (this should be the last option when choosing a method to remove roof sheeting), spray the asbestos cement roof sheeting with a PVA solution prior to removal. Ensure the PVA is dry before removing it so as to avoid a slip hazard. Once removed, spray the back (underside) of the asbestos cement with either a fine water spray or the PVA solution.
Where the asbestos cement product requires lowering to the ground, ensure this is done in a manner that will minimise the generation of respirable dust. Do not use chutes, ramps or similar gravity dependent devices. Examples of appropriate lowering methods for roof sheeting include:
by hand, over short distances
loading the wrapped sheets on to a cradle for support
using scissor lifts or similar devices
using scaffolds.
You should follow the cleaning, decontamination, waste removal and disposal procedures in this Code once the asbestos sheeting has been removed.
Where the area to be removed is greater than the size of an average domestic house or where considerable dust will be generated, you should use a full decontamination unit.
Ensure that clearance of the area has been completed and a clearance certificate has been issued prior to reoccupation of the area.
Personal decontamination must be carried out in accordance with the WHS Regulations and this Code.
Removal of floor tiles
Flooring products such as Polyvinyl chloride (PVC or vinyl) tiles often contain a few per cent (5–7 per cent) of very fine chrysotile. Black and brown thermoplastic tiles containing larger amounts and often visible clumps of chrysotile were also produced. Sheet floor coverings were sometimes backed with a thin layer of chrysotile paper. Some underfelts, such as hessian underlays for carpets and linoleum, were also manufactured containing asbestos. The mastics which were used to bond the floor covering to the surface could also contain asbestos. Some hard-wearing composite floors (for example, magnesium oxychloride) also contain about 2 per cent of mineral fibres, which could be asbestos.
Place a tool (such as a scraper or wide blade) between the tiles and lift the tile away from the floor, being careful to minimise breakage. A hammer or mallet can be used to tap the tool under firmly-adhered tiles to assist separating the tiles from the floor.
Minimise dust by spraying fine water mist under tiles as they are lifted.
Place the tiles into a 200 µm plastic waste bag or suitable alternate waste container dedicated for asbestos waste that is clearly labelled with an appropriate warning sign indicating asbestos waste.
Use the scraper to remove any adhesive that is left adhered to the floor after each tile has been removed and place this waste into the asbestos waste bag or suitable waste container.
The vinyl can be cut into strips prior to its removal to facilitate bagging, or it can be rolled into one roll and wrapped securely with plastic, making sure it is totally sealed.
If a heat source is used to soften the adhesive beneath a vinyl tile, care should be taken not to scorch or burn the tile. Burning or scorching vinyl tiles can result in the release of toxic decomposition products and generate a fire hazard. In some cases, the adhesive may contain asbestos.
Follow the cleaning, decontamination, waste removal and disposal procedures once the tiles have been removed.
Ensure that clearance of the area has been completed prior to reoccupation of the area.
Personal decontamination must be carried out in accordance with the WHS Regulations and this Code.
Removing bituminous (malthoid) products
This material is generally regarded as non-friable and includes bitumen products such as roofing felts and damp-proof courses that have been widely reinforced by the addition of asbestos, usually in the form of chrysotile paper. Bitumen-based wall and floor coverings were also produced.
Some mastics used to stick the bitumen products commonly had asbestos added to them for flexibility. Other sealants also had asbestos added to improve the performance of the product. When removing bituminous products:
seal access points (for example, skylights) with material such as 200 µm plastic sheeting and duct tape
where there are exhaust vents from gas fired equipment in the area, it is dangerous to seal over them. Turn the gas off if possible
cut and remove manageable sections. Place cut pieces in a lined skip or wrap in plastic sheeting
remove adhering material by dampening and gently scraping. Consider using an industrial vacuum cleaner fitted with a HEPA filter while scraping
remember that mastics are flexible and may require removal by using scraping and chipping tools. The pieces removed should be kept as intact as possible
if heating is used to soften the material to enable the material to be peeled, it is important not to burn the material, as this can release respirable asbestos fibres. Excessive heating is also likely to generate toxic fumes and gases and generate a fire hazard
collect all debris and dispose of waste according to the waste disposal procedures.
Personal decontamination must be carried out in accordance with the WHS Regulations and this Code.
Removal of ceiling tiles
False ceiling tiles or suspended ceilings sometimes need to be removed so maintenance work can be performed. If asbestos has been used on structural materials above a false ceiling there could be contamination on the upper surface of the tiles.
The minimum RPE suitable for this operation is a P1 or P2 filter with a half-face piece respirator.
If considerable amounts of asbestos dust or debris are likely to be involved, full-face air-purifying positive pressure respirators should be worn.
Any surface below the tiles that might be contaminated should be covered with plastic sheeting.
The first tile should be lifted carefully to minimise the disturbance of any asbestos fibres. The top
of each tile should be thoroughly vacuumed and wet wiped, where possible, prior to removing subsequent tiles.
Where non-asbestos ceiling tiles are to be reused, they should be covered with plastic as they are removed from the ceiling to prevent further dust settling on them.
Wrap the asbestos ceiling tiles in a double layer of heavy-duty, 200 μm thick plastic sheeting.
Waste containment, disposal and clearance must be carried out in accordance with the WHS Regulations and this Code.
Personal decontamination must be carried out in accordance with the WHS Regulations and this Code.
Removal of gaskets and rope seals
This material is generally regarded as friable. If there is any doubt, advice should be sought from
a person with knowledge and experience in dealing with asbestos.
Gaskets reinforced with asbestos were once used extensively in plant and equipment exposed to high temperatures and/or pressures. These gaskets were typically used between the flanges of pipes.
Asbestos rope was often used for lagging pipes and valves and for sealing hatches. It is likely that the asbestos in gaskets and rope from plant and equipment will be friable. When removing gaskets and rope seals:
ensure the plant or equipment is shut down and isolated
dismantle the equipment carefully. Protect any other components with plastic sheeting
ensure the plant and equipment has been made safe (pipework emptied, electrical supply isolated and equipment shutdown, etc.)
unbolt or unscrew the flange or dismantle the equipment
once accessible, dampen the asbestos with a fine water mist or similar. Continue dampening the asbestos as more of it is exposed/accessible
ease the gasket or rope seal away with the scraper and place into the waste container positioned directly beside/beneath it. Keep the area damp and scrape away any residue
consider using an industrial vacuum cleaner fitted with a HEPA filter while scraping.
Personal decontamination must be carried out in accordance with the WHS Regulations and this Code.
Removal of pipe lagging using a glove bag (small section)
Asbestos was widely used to insulate pipes, boilers and heat exchangers.
There are several types and forms of insulation, often with multi-layer construction. Pre-formed sections of asbestos insulation were made to fit the diameter of the pipe. These would be strapped on and calico-wrapped and sometimes painted (for example, ‘Decadex’ finish) or sealed with a hard plaster (often asbestos-containing) to protect against knocks and abrasion. Other types of asbestos-containing felts, blankets, tapes, ropes and corrugated papers were also used. For bends and joins, ensure the plant and equipment has been made safe (for example, pipework emptied, electrical supply isolated and equipment shut down).
Set-up/attach the glove bag and perform the removal work as described in this Code. Remove and dispose of waste according to the relevant sections of this Code.
Personal decontamination must be carried out in accordance with the WHS Regulations and this Code.
Fire retardant material
These are normally homogeneous coatings sprayed or trowelled onto reinforced concrete or steel columns or beams as fireproofing. Sprays were also commonly used on the underside of ceilings for fireproofing and sound and thermal insulation in many high-rise premises. Warehouses and factories commonly had sprayed asbestos applied to walls, ceilings and metal support structures for fireproofing.
Some fire doors contained loose asbestos insulation sandwiched between the wooden or metal facings to give them the appropriate fire rating. Loose asbestos was also packed around electrical cables, sometimes using chicken wire to contain it.
Mattresses containing loose asbestos were widely manufactured for thermal insulation. Acoustic insulation has been provided between floors by the use of loose asbestos in paper bags, and in some areas near removal works it is known that loose asbestos has been used as a readily available form of loft insulation.
Asbestos textiles were manufactured for primary heat (for example, insulation tapes and ropes)
or fire protection uses (for example, fire blankets, fire curtains and fire-resistant clothing).
Textiles were also used widely as a reinforcing material in friction products/composites.
It will depend on where the fire retardant material is located and the quantity of the material as to how the removal process is conducted, however the asbestos is friable and a Class A licensed asbestos removalist must perform the asbestos removal work.
An asbestos removal control plan must be developed.
Establish the extent of the removal area and move all items out of the area or cover them with 200 µm plastic sheeting if they could be contaminated during the removal work.
Develop an enclosure that allows smooth flow of air from the decontamination unit to the negative air units. In constructing the enclosure, pay particular attention to penetrations through the floor and ceiling/roof. Set up the enclosure and decontamination unit, and remove and dispose of asbestos.
Ensure all air-conditioning equipment has been shut and isolated/blanked from this area.
Maintain regular checks on the negative air unit and decontamination unit. An independent licensed asbestos assessor must conduct/control air monitoring throughout the asbestos removal work.
Clearance monitoring by an independent licensed asbestos assessor and the issue of a clearance certificate is required before re-entry into the removal work area.
Personal decontamination must be carried out in accordance with the WHS Regulations and this Code.
Removal of asbestos-backed vinyl and millboard from beneath a vinyl floor
As asbestos millboard is typically 100 per cent asbestos and very friable. A full enclosure with negative air extraction units must be used for this type of asbestos removal work.
The asbestos millboard should be wetted down as the vinyl is peeled from the floor, preferably with the millboard attached. The vinyl can be cut into strips prior to its removal to facilitate bagging, or it can be rolled into one roll and wrapped securely with plastic, making sure it is totally sealed. If the vinyl sheeting cannot be removed without leaving some of the asbestos millboard on the floor surface, the remaining asbestos millboard should be wetted down and, when thoroughly soaked, scraped off the floor surface.
Sufficient water should be used to dampen the asbestos millboard, but not so much that run-off or pools of contaminated water will occur.
If a heat source is used to soften the adhesive beneath a vinyl tile, care should be taken not to scorch or burn the tile. Burning or scorching vinyl tiles can result in the release of toxic decomposition products and generate a fire hazard.
Alternative removal methods should only be used if they do not result in excessive fibre release from the asbestos millboard and do not result in any additional hazard.
Personal decontamination must be carried out in accordance with the WHS Regulations and this Code.
0
0
0