Tariff Concession Revocation Order HS2007/578 Tariff Concession Order 0614566 (Cth)

Case
No judgment structure available for this case.

TARIFF CONCESSION REVOCATION ORDER

Under Section 269SD(2A) of the Customs Act 1901, I Robert Crawford a delegate of the Chief Executive Officer

(a) revoke Tariff Concession Order Number 9708969 made on 05.01.98, in respect of the goods described in TABLE A below.  This Revocation has effect from 31.12.06; and

(b) make in its place the Tariff Concession Orders described in TABLE B. The goods specified in Column 1 of TABLE B are goods to which the item in Part III of Schedule 4 to the Customs Tariff Act 1995 specified in Column 2 of TABLE B applies. The Order shall have effect from the date notified in paragraph (a) above as the date of effect for the Revocation.

TABLE A

               COLUMN 1

Description of Goods including the
Customs Tariff Classification

COLUMN 2

Schedule 4 Item Number Last date of effect

8708.99.99 PARTS, SUSPENSION, COMMERCIAL MOTOR VEHICLE, being ANY of the
 following:
   (a) spring hangers or frame shockhangers having:
           (i) a minimum yield strength of 380 mPa;
          (ii) a minimum tensile strength of 550 mPa;
         (iii) a minimum elongation of 6%;
          (iv) a general hardness range of 187-255 BHN;
           (v) attachment load capacity NOT exceeding 60 kN;
   (b) torque rods or transverse rods having:
           (i) 3 axis with end joint connections of either taper pin
               or bar pin;
          (ii) an attachment tensile and compressive load capacity
               NOT exceeding 35 kN;
   (c) top pads or transverse rod frame brackets having:
           (i) minimum yield strength of 300 mPa;
          (ii) minimum tensile strength of 450 mPa;
         (iii) minimum elongation of 12%;
          (iv) a general hardness range of 156-217 BHN;
   (d) spring seats or axle bottom caps having:
           (i) minimum yield strength of 380 mPa;
          (ii) minimum tensile strength of 550 mPa;
         (iii) minimum elongation of 6%;
          (iv) general hardness range of 187-255 BHN;
           (v) attachment load capacity NOT exceeding 35 kN;
   (e) transverse rod axle brackets having:
           (i) minimum yield strength of 300 mPa;
          (ii) minimum tensile strength of 550 mPa;
         (iii) minimum elongation of 20%;
          (iv) a general hardness range of 156-196 BHN;
   (f) cross channels or lower shock brackets having:
           (i) minimum tensile strength of 448 mPa;
          (ii) minimum yield strength of 350 mPa

Op. 10.10.97   - TC 9708969
50
31.12.06

This is page 1 of 2 Pages of the instrument.

   ..Robert Crawford......................

Dated 12 December 2006   Delegate of the Chief Executive Officer

Revocation Instrument HS2007/578

TABLE B

               COLUMN 1

Description of Goods including the
Customs Tariff Classification

COLUMN 2

Schedule 4 Item Number Last date of effect

8708.80.99 PARTS, SUSPENSION, COMMERCIAL MOTOR VEHICLE, being ANY of the
 following:
   (a) spring hangers or frame shockhangers having:
           (i) a minimum yield strength of 380 mPa;
          (ii) a minimum tensile strength of 550 mPa;
         (iii) a minimum elongation of 6%;
          (iv) a general hardness range of 187-255 BHN;
           (v) attachment load capacity NOT exceeding 60 kN;
   (b) torque rods or transverse rods having:
           (i) 3 axis with end joint connections of either taper pin
               or bar pin;
          (ii) an attachment tensile and compressive load capacity
               NOT exceeding 35 kN;
   (c) top pads or transverse rod frame brackets having:
           (i) minimum yield strength of 300 mPa;
          (ii) minimum tensile strength of 450 mPa;
         (iii) minimum elongation of 12%;
          (iv) a general hardness range of 156-217 BHN;
   (d) spring seats or axle bottom caps having:
           (i) minimum yield strength of 380 mPa;
          (ii) minimum tensile strength of 550 mPa;
         (iii) minimum elongation of 6%;
          (iv) general hardness range of 187-255 BHN;
           (v) attachment load capacity NOT exceeding 35 kN;
   (e) transverse rod axle brackets having:
           (i) minimum yield strength of 300 mPa;
          (ii) minimum tensile strength of 550 mPa;
         (iii) minimum elongation of 20%;
          (iv) a general hardness range of 156-196 BHN;
   (f) cross channels or lower shock brackets having:
           (i) minimum tensile strength of 448 mPa;
          (ii) minimum yield strength of 350 mPa

Op. 01.01.07   - TC 0614566
50

This is page 2 of 2 Pages of the instrument.

   ..Robert Crawford......................

Dated 12 December 2006   Delegate of the Chief Executive Officer

Revocation Instrument HS2007/578

Actions
Download as PDF Download as Word Document


Cases Citing This Decision

0

Cases Cited

0

Statutory Material Cited

0