Queensland Building Services Authority Amendment Regulation (No. 2) 2002 (Qld)

Queensland Building Services Authority Amendment Regulation (No. 2) 2002

Queensland Subordinate Legislation 2002 No. 190 Queensland Building Services Authority Act 1991 QUEENSLAND BUILDING SERVICES AUTHORITY AMENDMENT REGULATION (No. 2) 2002 TABLE OF PROVISIONS Section Page 1 Short title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Regulation amended . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 Amendment of s 3 (Deﬁnitions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 Amendment of s 3A (Work excluded from the ambit of the deﬁnition “building work”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5 Amendment of s 6 (Classes of licence—Act, s 30(2)) . . . . . . . . . . . . . . . . . 4 6 Amendment of s 7 (Requirements for contractor’s licence—Act, s 31) . . . . 4 7 Insertion of new s 11A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 11A Refund of annual licence fee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 8 Amendment of s 12 (Register—Act, s 39(2)(d)). . . . . . . . . . . . . . . . . . . . . . 5 9 Insertion of new s 35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 35 Transitional provision for Queensland Building Services Authority Amendment Regulation (No. 2) 2002 ................. 6 10 Amendment of sch 1 (Fees). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 11 Amendment of sch 2 (Classes of licences and licence requirements). . . . . . 6

s1 2 s3 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 1 Short title This regulation may be cited as the Queensland Building Services Authority Amendment Regulation (No. 2) 2002 . 2 Regulation amended This regulation amends the QueenslandBuildingServicesAuthorityRegulation 1992. 3 Amendment of s 3 (Deﬁnitions) (1) Section 3(1), deﬁnitions “building contractor’s licence” and “trade contractor’s licence”— omit . (2) Section 3(1)— insert — ‘ “Building Code of Australia” has the meaning given in the Building Act1975, section 3. 1 “builder contractor’s licence” means a licence of a class mentioned in schedule 2, part 1, 2, 30 or 31. “general repair” means repairs other than repairs carried out in connection with the preparation of a certiﬁcate of maintenance or a record of maintenance. “inspection” , for schedule 2, parts 58 to 66, means the process of examining, measuring, testing or otherwise comparing or evaluating an item, unit or system against an Australian Standard or a law of the Commonwealth or the State that relates to the item, unit or system. “maintenance” , for schedule 2, parts 58 to 66, means inspection and testing necessary to ensure that a ﬁre protection system and any other 1 Building Act 1975 , section 3 (Deﬁnitions)— “Building Code of Australia” means the edition, current at the relevant time, of the Building Code of Australia (including the Queensland Appendix) published by the body known as the Australian Building Codes Board and includes the edition as amended from time to time by amendments published by the board.

s4 3 s4 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ﬁre safety measures continue to operate at their original performance level and in accordance with any relevant Australian Standards. “occupational licence” means a licence or registration for an occupation that is— (a) issued to a person by an entity other than the authority; and (b) required by the person to carry out the occupation. “testing” , for schedule 2, parts 58 to 66, means determining 1 or more characteristics of a given product, process or service according to speciﬁed procedures and relevant Australian Standards. “trade contractor’s licence” means a licence mentioned in schedule 2, parts 3 to 24 or 32 to 112.’. 4 Amendment of s 3A (Work excluded from the ambit of the deﬁnition “building work”) (1) Section 3A(1)(b)— omit, insert — ‘(b) work of a value of less than $1 100, unless the work is within the scope of work of a licence provided for in schedule 2, part 7, 9, 10, 26 to 29, 39 to 41, 58 to 66 or 101.’. (2) Section 3A(1)(d) to (f)— omit, insert — ‘(d) work performed by an architect in the architect’s professional practice; (e) work performed by an engineer in the engineer’s professional practice; (f) work performed by a licensed surveyor in the surveyor’s professional practice;’. (3) Section 3A(1)— insert — ‘(zb)the laying of asphalt or bitumen;

s5 4 s7 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (zc) work to ﬁnd out about, and report on, the presence of asbestos materials under the WorkplaceHealthandSafetyRegulation1997 , part 11, division 1; 2 (zd) an inspection, investigation or report for assessment of an insurance claim; (ze) work of the type usually performed by a locksmith, whether performed by a locksmith or another person.’. (4) Section 3A(3), deﬁnition “general repair”— omit . 5 Amendment of s 6 (Classes of licence—Act, s 30(2)) (1) Section 6(2)— omit . (2) Section 6(3)— renumber as section 6(2). 6 Amendment of s 7 (Requirements for contractor’s licence—Act, s 31) Section 7(2), from ‘For a class’ to ‘24’— omit, insert — ‘For a class of licence other than a class mentioned in schedule 2, parts 1, 7, 9, 10 and 58 to 66’. 7 Insertion of new s 11A After section 11— insert — 2 WorkplaceHealthandSafetyRegulation1997 , part 11 (Asbestos), division 1 (On-site management of asbestos materials)

s8 5 s9 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘11A Refund of annual licence fee ‘ (1) The authority may refund the unexpired part of the annual licence fee paid by a licensee if— (a) the licensee surrenders the licence before the expiry date for the licence; or (b) the licensee dies during the licence period. ‘ (2) The unexpired part is the amount worked out using the formula— A- ---- L- ---- F- -- 1- - × - 2- --- W- ----- M- --- where— “ALF” means the annual licence fee paid by the licensee. “WM” means the whole months before the expiry date for the licence. ‘ (3) For the purpose of subsection (2), a whole month means a month beginning on the day of the calendar month on which the licence was issued and ending on the day before the corresponding day of the next calendar month. Example of whole month — For a licence issued on 7 March in a year—a month beginning on 7 March and ending on 6 April. ’. 8 Amendment of s 12 (Register—Act, s 39(2)(d)) Section 12(1)(a), from ‘holds’ to ‘licence’— omit, insert — ‘holds a licence that authorises the licensee to carry out residential construction work’. 9 Insertion of new s 35 After section 34— insert—

s 10 6 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘35 Transitional provision for Queensland Building Services Authority Amendment Regulation (No. 2) 2002 ‘ (1) This section applies to a person who held a licence under schedule 2, part 25 immediately before the commencement of the amending regulation. ‘ (2) The person is taken to hold a corresponding licence immediately after the commencement of the amending regulation. ‘ (3) The person’s corresponding licence is otherwise unaffected, for example, the licence is taken to be subject to the same conditions as the person’s licence under schedule 2, part 25. ‘ (4) In this section— “amending regulation” means the Queensland Building Services Authority Amendment Regulation (No. 2) 2002. “corresponding licence” means a licence of a class that has substantially the same scope of work as a licence under schedule 2, part 25.’. 10 Amendment of sch 1 (Fees) Schedule 1, items 1(a)(i)(C), 1(b)(iii), 2(a)(i)(C), and 2(b)(iii), ‘building contractor’s licence’— omit, insert — ‘builder contractor’s licence’. 11 Amendment of sch 2 (Classes of licences and licence requirements) (1) Schedule 2, part 9, section 2, from ‘sites’ to ‘control.’— omit, insert — ‘a site for termite control in connection with the construction of a building on the site.’. (2) Schedule 2, part 10, section 3, ‘Plumbing and Draining Licence’— omit, insert — ‘plumber’s licence and drainer’s licence’. (3) Schedule 2, part 17, section(3)(b), ‘attainment’— omit, insert —

s 11 7 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘a certiﬁcate’. (4) Schedule 2, part 22, section(3)(c), ‘attainment’— omit, insert — ‘a certiﬁcate’. (5) Schedule 2, part 25— omit . (6) Schedule 2— insert— ‘PART 30—GENERAL BUILDING RESTRICTED TO 1 STOREY LICENCE ‘1 Licence class ‘General building restricted to 1 storey. ‘2 Scope of work ‘ (1) All classes of building work (other than building work for which a house building licence is required) to a maximum of 1 storey only, using conventional construction methods to a minimum level of Type C construction as referred to in the Building Code of Australia. ‘ (2) The preparation of plans and speciﬁcations if the plans and speciﬁcations are— (a) for the licensee’s personal use; or (b) for use in building work to be performed by the licensee personally. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of any of the following courses— (i) Bachelor of Applied Science (Construction Management) CN51 (QUT); (ii) General Builders Registration CNB29 (TAFE);

s 11 8 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (iii) Diploma of Building CNBUI013 (TAFE); (iv) Certiﬁcate IV in Building CNBUI012 (TAFE); (v) House Builders Registration CNB28 (TAFE); (vi) 11019 Certiﬁcate IV conducted by the Queensland Master Builders Association; (vii) a course the authority considers is at least equivalent to a course mentioned in paragraph (a)(i) to (vi); (b) if there are relevant national competency standards for the class of licence—attainment of recognition of the required competency for the class of licence from an approved authority for the class of licence; (c) if there is no relevant national competency standard for the class of licence—attainment of recognition of the required competency against draft competency standards (level 4) from an approved assessor; (d) possession of a current house building licence. ‘4 Experience requirements ‘Two years practical and supervisory experience in the scope of work for the class. ‘5 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 31—GENERAL BUILDING RESTRICTED TO 3 STOREYS LICENCE ‘1 Licence class ‘General building restricted to 3 storeys.

s 11 9 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘2 Scope of work ‘ (1) All classes of building work (other than building work for which a house building licence is required) to a maximum of 3 storeys above a car park. ‘ (2) The preparation of plans and speciﬁcations if the plans and speciﬁcations are— (a) for the licensee’s personal use; or (b) for use in building work to be performed by the licensee personally. ‘3 Technical qualiﬁcations ‘Successful completion of any of the following courses— (a) Bachelor of Applied Science (Construction Management) CN51 (QUT); (b) General Builders Registration CNB29 (TAFE); (c) Diploma of Building CNBUI013 (TAFE); (d) General Builders Licence Course CNBUI008 (TAFE); (e) a course the authority considers is at least equivalent to a course mentioned in paragraphs (a) to (d). ‘4 Experience requirements ‘Two years practical and supervisory experience in the scope of work for the class. ‘5 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 10 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 32—BUILDING RESTRICTED TO ALTERATIONS AND ADDITIONS LICENCE ‘1 Licence class ‘Building restricted to alterations and additions. ‘2 Scope of work ‘ (1) Preparation, fabrication or erection of building components as part of work carried out during the process of addition to, or alteration or extension of, attached or detached buildings or structural work of the nature of— (a) framing; or (b) internal or external ﬁnishing; or (c) internal or external joinery; or (d) outdoor construction. ‘ (2) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a bricklaying, carpentry and joinery, painting, plastering, plumbing or tiling apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed bricklayer, carpenter and joiner, painter, plasterer, plumber or tiler; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation.

s 11 11 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 33—BUILDING RESTRICTED TO EXTERNAL FINISHES LICENCE ‘1 Licence class ‘Building restricted to external ﬁnishes. ‘2 Scope of work ‘ (1) Frame preparation, straightening, bracing and sarking and ﬂashings for ﬁxing of external cladding to a framed wall already containing window or door frames. ‘ (2) Installation of ﬁxing materials including patented fasteners and adhesives for wall cladding. ‘ (3) Fixing timber weatherboards, chamferboards, manufactured boards, sheeting, sidings to timber or metal framed walls. ‘ (4) Framing and sheeting of eaves. ‘ (5) Construction of entrances, porches and other exterior ﬁnishing details. ‘ (6) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a carpentry and joinery apprenticeship;

s 11 12 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (b) a recognition certiﬁcate as a qualiﬁed carpenter and joiner; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 34—BUILDING RESTRICTED TO BUILDING REMOVAL LICENCE ‘1 Licence class ‘Building restricted to building removal. ‘2 Scope of work ‘ (1) Preparation of buildings for removal. ‘ (2) Preparation of new sites for relocation of buildings including site set-out and boundary line measurement according to plans and speciﬁcations. ‘ (3) Re-siting of buildings. ‘ (4) Raising of buildings and positioning of stumps or other subﬂoor structure to support the buildings.

s 11 13 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘ (5) Restoration or reinstatement of buildings to useable and safe state including, for example, cladding, ﬂoor, roof or wall framing, repairing or replacing railings, rooﬁng or stairs. ‘ (6) Siting relocatable buildings. ‘ (7) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘A qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 35—BUILDING RESTRICTED TO RENOVATIONS, REPAIRS AND MAINTENANCE LICENCE ‘1 Licence class ‘Building restricted to renovations, repairs and maintenance. ‘2 Scope of work ‘ (1) Replace, repair and maintain but not initially install the following—

s 11 14 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (a) interior or exterior door or window frames and hinged, sliding, or roller doors or windows; (b) weather prooﬁng of door or window surrounds; (c) interior or exterior hardware to suit ﬁtments and accessories, including, for example, handles, hinges and locks; (d) external ﬁnishes; (e) outdoor construction; (f) concrete surfaces; (g) decking, ﬂooring, ramps, stairs or stumps; (h) interior ﬁnishes; (i) ceiling and wall linings; (j) joinery including, for example, architraves, joints and skirtings; (k) internal built-in ﬁtments; (l) ﬂoor and wall tiling; (m) paint and wallpaper; (n) wet areas. ‘ (2) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a carpentry and joinery, painting, plastering or tiling apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed carpenter and joiner, painter, plasterer or tiler; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation.

s 11 15 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 36—BUILDING RESTRICTED TO RENOVATIONS—WET AREAS LICENCE ‘1 Licence class ‘Building restricted to renovations (wet areas). ‘2 Scope of work ‘ (1) Installation of framing, linings, ﬂashings and sealants to provide effective waterprooﬁng of wet areas within buildings. ‘ (2) Installation of wet area linings. ‘ (3) Construction and ﬁtting of wet area ﬁtments and built-in units. ‘ (4) Installation or repair wall or ﬂoor tiling. ‘ (5) Paint repairs. ‘ (6) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations and requirement ‘Any 1 of the following— (a) successful completion of a carpentry and joinery, painting, plumbing or tiling apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed carpenter and joiner, painter, plumber or tiler;

s 11 16 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 37—BUILDING RESTRICTED TO REPAIRS AND MAINTENANCE LICENCE ‘1 Licence class ‘Building restricted to repairs and maintenance. ‘2 Scope of work ‘Repairing or maintaining buildings if the existing structural fabric of the building is not altered and if— (a) the total value of the building work does not exceed $10 000.00; and (b) the contract does not involve the performance of building work for which an occupational licence is required; and (c) the work does not alter or affect a part of the building which is loadbearing or a structural member; and (d) the work does not involve adding a new element to the building, including, for example, a column, ﬂoor, foundation or wall; and

s 11 17 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (e) the contract work performed does not involve the performance of building work that could reasonably be performed by a licensed trade contractor with a single class of licence. Examples of single classes of licences — Painting licence, wall and ﬂoor tiling licence. ‘3 Technical qualiﬁcations ‘A qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 38—BUILDING RESTRICTED TO NON–STRUCTURAL RENOVATIONS LICENCE ‘1 Licence class ‘Building restricted to non-structural renovations. ‘2 Scope of work ‘Replace, repair or maintain any part of a building that is not loadbearing or a structural member.

s 11 18 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘3 Technical qualiﬁcations ‘A qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 39—COMPLETED BUILDING INSPECTION LICENCE ‘1 Licence class ‘Completed building inspection. ‘2 Scope of work ‘Inspection or investigation of, and the provision of advice or a report about, a completed building. ‘3 Technical qualiﬁcations ‘Either— (a) current general building and house building licences; or (b) current accreditation as a building surveyor or assistant building surveyor by the Building Surveyors and Allied Professions

s 11 19 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 Accreditation Board Incorporated or the Australian Institute of Building Surveyors ACN 004 540 836. ‘4 Experience requirements ‘Two years practical experience with the scope of work for the class. ‘5 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 40—COMPLETED BUILDING INSPECTION RESTRICTED TO RESIDENTIAL BUILDINGS LICENCE ‘1 Licence class ‘Completed building inspection restricted to residential buildings. ‘2 Scope of work ‘Inspection or investigation of, and the provision of advice or a report about, a completed residential building. ‘3 Technical qualiﬁcations ‘Either— (a) a current house building licence; or (b) current accreditation as a building surveyor or assistant building surveyor by the Building Surveyors and Allied Professions Accreditation Board Incorporated or the Australian Institute of Building Surveyors ACN 004 540 836.

s 11 20 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘4 Experience requirements ‘Two years practical experience with the scope of work for the class. ‘5 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 41—COMPLETED BUILDING INSPECTION RESTRICTED TO COMMERCIAL BUILDINGS LICENCE ‘1 Licence class ‘Completed building inspection restricted to commercial buildings. ‘2 Scope of work ‘Inspection or investigation of, and the provision of advice or a report about, a completed commercial building. ‘3 Technical qualiﬁcations ‘Either— (a) a current general building licence; or (b) current accreditation as a building surveyor or assistant building surveyor by the Building Surveyors and Allied Professions Accreditation Board Incorporated or the Australian Institute of Building Surveyors ACN 004 540 836. ‘4 Experience requirements ‘Two years practical experience with the scope of work for the class.

s 11 21 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 42—BUILDING INTERIOR DESIGN LICENCE ‘1 Licence class ‘Building interior design. ‘2 Scope of work ‘ (1) Preparation of plans and speciﬁcations for building work associated with the interior design of all types of buildings except where the work affects a part of the building which is loadbearing or a structural member. ‘ (2) Contract administration associated with interior design of all types of buildings. ‘3 Technical qualiﬁcations ‘Graduate Diploma in Interior Design AR62 (QUT) or a qualiﬁcation the authority considers is at least equivalent to the Graduate Diploma. ‘4 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘5 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 22 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 43—RESIDENTIAL INTERIOR DESIGN LICENCE ‘1 Licence class ‘Residential interior design licence. ‘2 Scope of work ‘( 1) Preparation of plans and speciﬁcations for building work associated with the interior design of a residence except where the work affects a part of the building which is loadbearing or a structural member. ‘( 2) Contract administration associated with interior design of a residence. ‘3 Technical qualiﬁcations ‘Either— (a) Diploma in Interior Technology (TAFE) or a qualiﬁcation the authority considers is at least equivalent to the diploma; or (b) Graduate Diploma in Interior Design AR62 (QUT) or a qualiﬁcation the authority considers is at least equivalent to the Graduate Diploma. ‘4 Managerial qualiﬁcations ‘If the applicant does not hold the qualiﬁcation mentioned in section 3(b)—an approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 23 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 44—HYDRAULIC SERVICES DESIGN LICENCES ‘1 Licence classes ‘ (1) Hydraulic services design. ‘ (2) Hydraulic services design excluding on-site domestic waste water management. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)—preparation of plans, speciﬁcations and documents, associated with the following building services— (a) sanitary drainage, soil waste and venting; (b) trade waste drainage, plumbing and venting; (c) cold and hot water; (d) rainwater and stormwater drainage; (e) gas services; (f) ﬁre hydrant and hose reel services, with or without pumps; (g) commercial, residential and domestic ﬁre sprinklers, deluge and wall wetting sprinklers (drenchers); (h) on-site domestic waste water management. ‘ (2) For the licence class mentioned in section 1(2)—preparation of plans, speciﬁcations and documents, associated with the building services mentioned in subsection (1)(a) to (g). ‘3 Technical qualiﬁcations ‘ (1) For the licence class mentioned in section 1(1)— (a) successful completion of a Diploma of Engineering—Construction Hydraulics CNO171 (TAFE) or a qualiﬁcation the authority considers is at least equivalent to the diploma; and

s 11 24 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (b) successful completion of Site Assessment and Design Course CNQ12 (TAFE) or a course the authority considers is at least equivalent to the CNQ12 course. ‘ (2) For the licence class mentioned in section 1(2)—a Diploma of Engineering—Construction Hydraulics CNO171 (TAFE) or a qualiﬁcation the authority considers is at least equivalent to the diploma. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work of the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 45—BRICKLAYING RESTRICTED TO BRICK AND SEGMENTAL PAVING LICENCE ‘1 Licence class ‘Bricklaying restricted to brick and segmental paving. ‘2 Scope of work ‘ (1) Site investigation and sub-base preparation. ‘( 2) Setting out, levelling and installation of drainage. ‘ (3) Laying concrete and other sub-base materials. ‘ (4) Laying paving, including jointing, bonding and coping. ‘( 5) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence.

s 11 25 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a bricklaying apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed bricklayer; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 46—BRICKLAYING RESTRICTED TO BLOCKLAYING LICENCE ‘1 Licence class ‘Bricklaying restricted to blocklaying licence. ‘2 Scope of work ‘Laying of concrete, glass, masonry, plaster, plastic, reconstituted material, stone, synthetic or terracotta blocks and building work directly associated with the installation and repair of such blocks. ‘3 Technical qualiﬁcations ‘Any 1 of the following—

s 11 26 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (a) successful completion of a bricklaying apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed bricklayer; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 47—CARPENTRY RESTRICTED TO FRAMING LICENCE ‘1 Licence class ‘Carpentry restricted to framing licence. ‘2 Scope of work ‘ (1) Fabrication and erection of frames. ‘ (2) Construction and installation of external stairs with open risers. ‘ (3) Fixing timber ﬂooring. ‘ (4) Installation of roof truss systems. ‘ (5) Fabrication and installation of fascia and barge boards. ‘ (6) Construction and installation of eaves and support framing. ‘ (7) Construction of gable and hip roof framing.

s 11 27 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘ (8) Fitting external doors, windows and window frames. ‘ (9) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a carpentry apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed carpenter and joiner; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 48—CARPENTRY RESTRICTED TO INTERNAL FINISHES LICENCE ‘1 Licence class ‘Carpentry restricted to internal ﬁnishes. ‘2 Scope of work ‘ (1) Installation of internal wall and ceiling coverings.

s 11 28 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘ (2) Installation of internal doors, jambs, skirtings and architraves. ‘ (3) Construction and installation of internal ﬁtments, built-in cupboards and wardrobe units and any other related joinery work. ‘ (4) Fabrication and installation of straight ﬂight and dog-legged staircases and handrails. ‘ (5) Installation of related hardware components to the internal ﬁnish of a building. ‘ (6) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a cabinet-making, carpentry or joinery apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed cabinet-maker, carpenter or joiner; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 29 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 49—CARPENTRY RESTRICTED TO OUTDOOR CONSTRUCTION LICENCE ‘1 Licence class ‘Carpentry restricted to outdoor construction. ‘2 Scope of work ‘ (1) Preparation, fabrication and erection of attached or detached building work for carports, decking, fences and gates, garden enclosures, gazebos or pergolas. ‘ (2) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence . ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a carpentry apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed carpenter; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 30 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 50—CARPENTRY RESTRICTED TO JOINERY PRODUCTS LICENCE ‘1 Licence class ‘Carpentry restricted to joinery products. ‘2 Scope of work ‘Installation of manufactured or prefabricated cabinet or joinery work. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a cabinet-making, carpentry or joinery apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed cabinet-maker, carpenter or joiner; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 31 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 51—CARPENTRY RESTRICTED TO LATTICE AND OTHER TIMBER WORK LICENCE ‘1 Licence class ‘Carpentry restricted to lattice and other timber work. ‘2 Scope of work ‘Fabrication and erection of lattice or other external and internal manufactured timber products. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a carpentry apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed carpenter; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 32 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 52—CONCRETING RESTRICTED TO CONCRETE REPAIRS LICENCE ‘1 Licence class ‘Concreting restricted to concrete repairs licence. ‘2 Scope of work ‘Maintenance or repair of concrete surfaces. ‘3 Technical qualiﬁcations ‘A qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 53—CONCRETING RESTRICTED TO LIGHT CONCRETING LICENCE ‘1 Licence class ‘Concreting restricted to light concreting.

s 11 33 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘2 Scope of work ‘ (1) General site work and preparation and installation of concrete for light concrete construction to 1 ﬂoor height. ‘ (2) Minor earthworks and excavating of footings. ‘ (3) Laying bedding material. ‘ (4) Installation of waterproof barriers. ‘ (5) Fixing edge boards and joints. ‘ (6) Placing and ﬁxing reinforcement to— (a) footings; or (b) slabs on the ground; or (c) suspended slabs; or (d) walls; or (e) columns and stairs. ‘ (7) Placing, vibrating, levelling and ﬁnishing of concrete, including colouring, patterning or special ﬁnishes. ‘ (8) Curing concrete. ‘ (9) Repairing concrete. ‘ (10) Construction of channels, driveways, kerbs and paths. ‘ (11) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence . ‘3 Technical qualiﬁcations ‘Either— (a) successful completion of Certiﬁcate II in Construction (Concrete Working Traineeship) CTQ001 (TAFE); or (b) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation.

s 11 34 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 54—CONCRETING RESTRICTED TO MINOR CONCRETE WORK LICENCE ‘1 Licence class ‘Concreting restricted to minor concrete work. ‘2 Scope of work ‘General site work, preparation and installation of concrete for the construction of channels, driveways, kerbs, paths, slabs for carports or non-habitable sheds, or outdoor sports slabs. ‘3 Technical qualiﬁcations ‘Either— (a) successful completion of Certiﬁcate II in Construction (Concrete Working Traineeship) CTQ001 (TAFE); or (b) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class.

s 11 35 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 55—CONCRETING RESTRICTED TO PILING AND FOUNDATIONS LICENCE ‘1 Licence class ‘Concreting restricted to piling and foundations. ‘2 Scope of work ‘Installation of driven piles of various materials by physical or mechanical means and preparation and installation of associated footing or foundations. ‘3 Technical qualiﬁcations ‘Either— (a) successful completion of Certiﬁcate II in Construction (Concrete Working Traineeship) CTQ001 (TAFE); or (b) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 36 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 56—CONCRETING RESTRICTED TO SPECIAL FINISHES LICENCE ‘1 Licence class ‘Concreting restricted to special ﬁnishes. ‘2 Scope of work ‘Finishing concrete with special ﬁnishes including, but not limited to, coating, colouring, exposed aggregate and stamping. ‘3 Qualiﬁcation ‘Either— (a) successful completion of Certiﬁcate II in Construction (Concrete Working Traineeship) CTQ001 (TAFE); or (b) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 37 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 57—CONCRETING RESTRICTED TO UNDERPINNING AND FOUNDATION REPAIR LICENCE ‘1 Licence class ‘Concreting restricted to underpinning and foundation repair. ‘2 Scope of work ‘Underpinning and repair (including pressure injection) of foundations and footings and the reinstatement of pathways. ‘3 Technical qualiﬁcations ‘A qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 58—FIRE FIGHTING APPLIANCES LICENCES ‘1 Licence classes ‘ (1) Fire ﬁghting appliances.

s 11 38 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘ (2) Fire ﬁghting appliances restricted to carrying out certain work. ‘ (3) Fire ﬁghting appliances restricted to certiﬁcation of, and preparation of reports about, certain work. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)— (a) carrying out installation and general repair of portable ﬁre ﬁghting appliances for a building, including, for example, wheeled ﬁre extinguishers, ﬁre hoses, ﬁre blankets and portable ﬁre extinguishers; and (b) carrying out maintenance of portable ﬁre ﬁghting appliances, ﬁre hose reels and ﬁre hydrants for a building; and (c) certiﬁcation of the installation of portable ﬁre ﬁghting appliances under the Standard Building Regulation 1993 ; and (d) preparation of a report for a certiﬁcate or record of maintenance of portable ﬁre ﬁghting appliances, ﬁre hydrants or hose reels. ‘ (2) For the licence class mentioned in section 1(2)—carrying out installation and general repair of portable ﬁre ﬁghting appliances for a building, including, for example, wheeled ﬁre extinguishers, ﬁre hoses, ﬁre blankets and portable ﬁre extinguishers. ‘ (3) For the licence class mentioned in section 1(3)— (a) carrying out maintenance of portable ﬁre ﬁghting appliances, ﬁre hose reels and ﬁre hydrants for a building; and (b) certiﬁcation of the installation of portable ﬁre ﬁghting appliances under the Standard Building Regulation 1993 ; and (c) preparation of a report for a certiﬁcate or record of maintenance of portable ﬁre ﬁghting appliances, ﬁre hydrants or hose reels. ‘3 Technical qualiﬁcations ‘ (1) For the licence class mentioned in section 1(1) or (2)— (a) successful completion of PRM20400 Certiﬁcate II in Asset Maintenance (Portable Fire Equipment Service Operations); or

s 11 39 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (b) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘ (2) For the licence class mentioned in section 1(3), either— (a) a qualiﬁcation mentioned in subsection (1); or (b) a written statement by Construction Training Queensland, or accreditation from the Fire Protection Contractors Registration Board, that a person has competency in all of the following— (i) category IAA—certiﬁcation of selection, location and installation of portable ﬁre appliances; (ii) category MAA—certiﬁcation of on-site maintenance of portable ﬁre appliances, wheeled ﬁre extinguishers and delivery lay-ﬂat ﬁre hoses; (iii) category MAB—certiﬁcation of workshop maintenance of portable ﬁre appliances, wheeled ﬁre extinguishers and delivery lay-ﬂat ﬁre hoses; (iv) category MAC—certiﬁcation of maintenance of ﬁre hose reel systems; (v) category MAD—certiﬁcation of maintenance of ﬁre hydrant systems. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class or work the authority is reasonably satisﬁed is the equivalent of the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 40 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 59—FIRE HYDRANTS AND FIRE HOSE REELS LICENCES ‘1 Licence classes ‘ (1) Fire hose reels and ﬁre hydrants. ‘ (2) Fire hose reels and ﬁre hydrants restricted to carrying out certain work. ‘ (3) Fire hose reels and ﬁre hydrants restricted to certiﬁcation of, and preparation of reports about, certain work. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)— (a) carrying out installation and general repair of ﬁre hose reels and ﬁre hydrants for a building; and (b) carrying out maintenance of ﬁre hose reels and ﬁre hydrants for a building; and (c) certiﬁcation of the installation of ﬁre hose reels and ﬁre hydrants for a building under the Standard Building Regulation 1993 ; and (d) preparation of a report for a certiﬁcate or record of maintenance of ﬁre hose reels and ﬁre hydrants for a building. ‘ (2) For the licence class mentioned in section 1(2)—carrying out installation and general repair of ﬁre hose reels and ﬁre hydrants for a building. ‘ (3) For the licence class mentioned in section 1(3)— (a) carrying out maintenance of ﬁre hose reels and ﬁre hydrants for a building; and (b) certiﬁcation of the installation of ﬁre hose reels and ﬁre hydrants for a building under the Standard Building Regulation 1993 ; and (c) preparation of a report for a certiﬁcate or record of maintenance of ﬁre hose reels and ﬁre hydrants for a building.

s 11 41 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘3 Technical qualiﬁcations ‘ (1) For the licence class mentioned in section 1(1)— (a) either— (i) possession of a plumber’s or water plumber’s licence endorsed ﬁre protection (hydrants and hose reels) issued by the Plumbers and Drainers Examination and Licensing Board; or (ii) possession of a restricted plumber’s ﬁre protection (hydrants and hose reels) licence issued by the Plumbers and Drainers Examination and Licensing Board; and (b) a written statement by Construction Training Queensland, or accreditation from the Fire Protection Contractors Registration Board, that a person has competency in all of the following— (i) category IAB—certiﬁcation of installation of ﬁre hose reel systems; (ii) category IAC—certiﬁcation of installation of ﬁre hydrant systems; (iii) category MAC—certiﬁcation of maintenance of ﬁre hose reel systems; (iv) category MAD—certiﬁcation of maintenance of ﬁre hydrant systems. ‘ (2) For the licence class mentioned in section 1(2)—a qualiﬁcation mentioned in subsection (1)(a). ‘ (3) For the licence class mentioned in section 1(3)—a qualiﬁcation mentioned in subsection (1)(b). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class or work the authority is reasonably satisﬁed is the equivalent of the scope of work for the class.

s 11 42 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 60—FIRE DETECTION SYSTEMS LICENCES ‘1 Licence classes ‘ (1) Fire detection systems. ‘ (2) Fire detection systems restricted to carrying out certain work. ‘ (3) Fire detection systems restricted to certiﬁcation of, and preparation of reports about, certain work. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)— ( a ) carrying out installation and general repair of a ﬁre detection and alarm system or emergency warning and communication system for a building; and (b) carrying out maintenance of a ﬁre detection and alarm system or emergency warning and communication system for a building; and ( c) certiﬁcation of the installation of a ﬁre detection and alarm system or emergency warning and communication system for a building under the Standard Building Regulation 1993 ; and ( d) preparation of a report for a certiﬁcate or record of maintenance of a ﬁre detection and alarm system or emergency warning and communication system for a building. ‘ (2) For the licence class mentioned in section 1(2)—carrying out installation and general repair of a ﬁre detection and alarm system or emergency warning and communication system for a building. ‘ (3) For the licence class mentioned in section 1(3)—

s 11 43 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (a) carrying out maintenance of a ﬁre detection and alarm system or emergency warning and communication system for a building; and (b) certiﬁcation of the installation of a ﬁre detection and alarm system or emergency warning and communication system for a building under the Standard Building Regulation 1993 ; and ( c) preparation of a report for a certiﬁcate or record of maintenance of a ﬁre detection and alarm system or emergency warning and communication system for a building. ‘3 Technical qualiﬁcations ‘ (1) For the licence class mentioned in section 1(1) or (3)—a written statement by Construction Training Queensland, or accreditation from the Fire Protection Contractors Registration Board, that a person has competency in all of the following— (a) category IAD—certiﬁcation of installation of ﬁre detection and alarm systems; (b) category IAE—certiﬁcation of installation of emergency warning and intercommunication systems; (c) category MAE—certiﬁcation of maintenance of ﬁre detection and alarm systems; (d) category MAF—certiﬁcation of maintenance of emergency warning and intercommunication systems. ‘ (2) For the licence class mentioned in section 1(2)—any 1 of the following— (a) an electrical contractor’s licence under the Electricity Regulation1994 , section 52; (b) successful completion of Certiﬁcate IV in Electrical Contracting Studies CNO174 (TAFE); (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; (d) a written statement by Construction Training Queensland, or accreditation from the Fire Protection Contractors Registration Board, that a person has competency in all of the following—

s 11 44 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (i) category IAD—certiﬁcation of installation of ﬁre detection and alarm systems; (ii) category IAE—certiﬁcation of installation of emergency warning and intercommunication systems; (iii) category MAE—certiﬁcation of maintenance of ﬁre detection and alarm systems; (iv) category MAF—certiﬁcation of maintenance of emergency warning and intercommunication systems. ‘4 Managerial qualiﬁcations ‘The managerial qualiﬁcation is either— (a) an approved managerial qualiﬁcation; or (b) successful completion of Certiﬁcate IV in Electrical Contracting Studies CNO174 (TAFE). ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class or work the authority is reasonably satisﬁed is the equivalent of the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 61—FIRE SPRINKLER SYSTEMS (DOMESTIC AND RESIDENTIAL) LICENCES ‘1 Licence classes ‘ (1) Fire sprinkler systems (domestic and residential). ‘ (2) Fire sprinkler systems (domestic and residential) restricted to carrying out certain work.

s 11 45 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘ (3) Fire sprinkler systems (domestic and residential) restricted to certiﬁcation of, and preparation of reports about, certain work. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)— (a) carrying out installation and general repair of ﬁre sprinkler systems for a domestic or residential building as speciﬁed in AS 2118.4–1995 and AS 2118.5–1995; and (b) carrying out maintenance of ﬁre sprinkler systems for a domestic or residential building as speciﬁed in AS 2118.4–1995 and AS 2118.5–1995; and (c) certiﬁcation under the Standard Building Regulation 1993 of the installation of ﬁre sprinkler systems for a domestic or residential building as speciﬁed in AS 2118.4–1995 and AS 2118.5–1995; and (d) preparation of a report for a certiﬁcate or record of maintenance of ﬁre sprinkler systems for a domestic or residential building as speciﬁed in AS 2118.4–1995 and AS 2118.5–1995. ‘ (2) For the licence class mentioned in section 1(2)—carrying out installation and general repair of ﬁre sprinkler systems for a domestic or residential building as speciﬁed in AS 2118.4–1995 and AS 2118.5–1995. ‘ (3) For the licence class mentioned in section 1(3)— (a) carrying out maintenance of ﬁre sprinkler systems for a domestic or residential building as speciﬁed in AS 2118.4–1995 and AS 2118.5–1995; and (b) certiﬁcation under the Standard Building Regulation 1993 of the installation of ﬁre sprinkler systems for a domestic or residential building as speciﬁed in AS 2118.4–1995 and AS 2118.5–1995; and (c) preparation of a report for a certiﬁcate or record of maintenance of ﬁre sprinkler systems for a domestic or residential building as speciﬁed in AS 2118.4–1995 and AS 2118.5–1995.

s 11 46 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘3 Technical qualiﬁcations ‘ (1) For the licence class mentioned in section 1(1)— (a) either— (i) possession of a plumber’s or water plumber’s licence endorsed ﬁre protection (domestic and residential) issued by the Plumbers and Drainers Examination and Licensing Board; or (ii) possession of a restricted plumber’s ﬁre protection (domestic and residential) licence issued by the Plumbers and Drainers Examination and Licensing Board; and (b) either— (i) a written statement by Construction Training Queensland, or accreditation from the Fire Protection Contractors Registration Board, that a person has competency in both of the following— (A) category IAK—certiﬁcation of installation of residential life safety sprinkler systems; (B) category MAL—certiﬁcation of maintenance of residential life safety sprinkler systems; or (ii) successful completion of the domestic and residential ﬁre sprinkler systems course MPA001 conducted by the Masters Plumbers’ Association of Queensland. ‘ (2) For the licence class mentioned in section 1(2)—a qualiﬁcation mentioned in subsection (1)(a). ‘ (3) For the licence class mentioned in section 1(3)—a qualiﬁcation mentioned in subsection (1)(b). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class or work the authority is reasonably satisﬁed is the equivalent of the scope of work for the class.

s 11 47 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 62—FIRE SPRINKLER SYSTEMS (OTHER THAN DOMESTIC AND RESIDENTIAL) LICENCES ‘1 Licence classes ‘ (1) Fire sprinkler systems (other than domestic and residential). ‘ (2) Fire sprinkler systems (other than domestic and residential) restricted to carrying out certain work. ‘ (3) Fire sprinkler systems (other than domestic and residential) restricted to certiﬁcation of, and preparation of reports about, certain work. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)— (a) carrying out installation and general repair of ﬁre sprinkler systems for a building other than a domestic or residential building; and (b) carrying out maintenance of ﬁre sprinkler systems for a building other than a domestic or residential building; and (c) certiﬁcation of the installation of ﬁre sprinkler systems for a building other than a domestic or residential building under the Standard Building Regulation 1993 ; and (d) preparation of a report for a certiﬁcate or record of maintenance of ﬁre sprinkler systems for a building other than a domestic or residential building. ‘ (2) For the licence class mentioned in section 1(2)—carrying out installation and general repair of ﬁre sprinkler systems for a building other than a domestic or residential building. ‘ (3) For the licence class mentioned in section 1(3)—

s 11 48 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (a) carrying out maintenance of ﬁre sprinkler systems for a building other than a domestic or residential building; and (b) certiﬁcation of the installation of ﬁre sprinkler systems for a building other than a domestic or residential building under the Standard Building Regulation 1993 ; and (c) preparation of a report for a certiﬁcate or record of maintenance of ﬁre sprinkler systems for a building other than a domestic or residential building. ‘3 Technical qualiﬁcations ‘ (1) For the licence class mentioned in section 1(1)— (a) either— (i) possession of a plumber’s or water plumber’s licence endorsed ﬁre protection (commercial and industrial) issued by the Plumbers and Drainers Examination and Licensing Board; or (ii) possession of a restricted plumber’s ﬁre protection (commercial and industrial) licence issued by the Plumbers and Drainers Examination and Licensing Board; and (b) a written statement by Construction Training Queensland, or accreditation from the Fire Protection Contractors Registration Board, that a person has competency in both of the following— (i) category IAF—certiﬁcation of installation of engineered water discharging (based) ﬁre systems (deluge, drencher, sprinkler and spray systems); (ii) category MAG—certiﬁcation of maintenance of engineered water discharging (based) ﬁre systems (deluge, drencher, sprinkler and spray systems). ‘ (2) For the licence class mentioned in section 1(2)—a qualiﬁcation mentioned in subsection (1)(a). ‘ (3) For the licence class mentioned in section 1(3)—a qualiﬁcation mentioned in subsection (1)(b).

s 11 49 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class or work the authority is reasonably satisﬁed is the equivalent of the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 63—FIRE SUPPRESSION SYSTEMS—SPECIAL HAZARDS LICENCES ‘1 Licence classes ‘ (1) Fire suppression systems (special hazards). ‘ (2) Fire suppression systems (special hazards) restricted to carrying out certain work. ‘ (3) Fire suppression systems (special hazards) restricted to certiﬁcation of, and preparation of reports about, certain work. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)— (a) carrying out installation and general repair of specialist based ﬁre suppression systems for a building; and (b) carrying out maintenance of specialist based ﬁre suppression systems for a building; and (c) certiﬁcation of the installation of specialist based ﬁre suppression systems for a building under the StandardBuildingRegulation1993 ; and

s 11 50 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (d) preparation of a report for a certiﬁcate or record of maintenance of specialist based ﬁre suppression systems for a building. ‘ (2) For the licence class mentioned in section 1(2)—carrying out installation and general repair of specialist based ﬁre suppression systems for a building. ‘ (3) For the licence class mentioned in section 1(3)— (a) carrying out maintenance of specialist based ﬁre suppression systems for a building; and (b) certiﬁcation of the installation of specialist based ﬁre suppression systems for a building under the StandardBuildingRegulation1993 ; and (c) preparation of a report for a certiﬁcate or record of maintenance of specialist based ﬁre suppression systems for a building. ‘3 Technical qualiﬁcations ‘ (1) For a licence mentioned in section 1(1) or (3)—a written statement by Construction Training Queensland, or accreditation from the Fire Protection Contractors Registration Board, that a person has competency in all of the following— (a) category IAG—certiﬁcation of installation of foam ﬁre systems; (b) category IAH—certiﬁcation of installation of halon ﬁre systems; (c) category IAI—certiﬁcation of installation of chemical ﬁre systems; (d) category IAJ—certiﬁcation of installation of gaseous systems; (e) category MAH—certiﬁcation of maintenance of foam ﬁre systems; (f) category MAI—certiﬁcation of maintenance of halon ﬁre systems; (g) category MAJ—certiﬁcation of maintenance of chemical ﬁre systems; (h) category MAK—certiﬁcation of maintenance of gaseous systems. ‘ (2) For a licence mentioned in section 1(2), any 1 of the following—

s 11 51 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (a) a written statement or accreditation mentioned in subsection (1); (b) demonstrated competence against all the following national competency standards— (i) SE3223A—install special hazard systems; (ii) PRMPFES29A—install, inspect and maintain a pre-engineered dry chemical powder ﬁre suppression system; (iii) PRMPFES30A—install, inspect and maintain a pre-engineered wet chemical ﬁre suppression system; (iv) PRMPFES31A—inspect and service a self-contained water mist ﬁre suppression system; (v) PRMPFES25A—inspect and service a gaseous ﬁre suppression system; (vi) PRMPFES27A—install, inspect and maintain a pre-engineered ﬁre suppression system; (c) for a particular ﬁre suppression system—certiﬁcation by the manufacturer or supplier of the system that a person has satisfactorily completed a course about the installation, maintenance and general repair of the system. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class or work the authority is reasonably satisﬁed is the equivalent of the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 52 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 64—PASSIVE FIRE EQUIPMENT (WALL AND CEILING LINING) LICENCE ‘1 Licence class ‘Passive ﬁre equipment (wall and ceiling lining). ‘2 Scope of work ‘ (1) Carrying out installation, maintenance and general repair of wall and ceiling lining for a building. ‘ (2) Certiﬁcation of the installation of wall and ceiling lining for a building under the Standard Building Regulation 1993 . ‘ (3) Preparation of a report for a certiﬁcate or record of maintenance of wall and ceiling lining for a building. ‘3 Technical qualiﬁcations ‘Successful completion of 14865 Course in Passive Fire Protection conducted by the Association of Wall and Ceiling Industries Queensland–Union of Employers and either— (a) successful completion of Certiﬁcate III in General Construction (Wall and Ceiling Lining) BCG30298; or (b) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience with the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 53 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 65—PASSIVE FIRE EQUIPMENT (FIRE DOORS AND FIRE SHUTTERS) LICENCES ‘1 Licence classes ‘ (1) Passive ﬁre equipment (ﬁre doors and ﬁre shutters). ‘ (2) Passive ﬁre equipment (ﬁre doors and ﬁre shutters) restricted to carrying out certain work. ‘ (3) Passive ﬁre equipment (ﬁre doors and ﬁre shutters) restricted to certiﬁcation of, and preparation of reports about, certain work. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)— (a) carrying out installation and general repair of ﬁre doors and ﬁre shutters for a building; and (b) carrying out maintenance of ﬁre doors and ﬁre shutters for a building; and (c) certiﬁcation of the installation of ﬁre doors and ﬁre shutters for a building under the Standard Building Regulation 1993 ; and (d) preparation of a report for a certiﬁcate or record of maintenance of ﬁre doors and ﬁre shutters for a building. ‘ (2) For the licence class mentioned in section 1(2)—carrying out installation and general repair of ﬁre doors and ﬁre shutters for a building. ‘ (3) For the licence class mentioned in section 1(3)— (a) carrying out maintenance of ﬁre doors and ﬁre shutters for a building; and (b) certiﬁcation of the installation of ﬁre doors and ﬁre shutters for a building under the Standard Building Regulation 1993 ; and (c) preparation of a report for a certiﬁcate or record of maintenance of ﬁre doors and ﬁre shutters for a building. ‘3 Technical qualiﬁcations ‘ (1) For the licence class mentioned in section 1(1)—

s 11 54 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (a) any 1 of the following— (i) successful completion of Certiﬁcate III in General Construction (Carpentry—Framework/Formwork/ Finishing) BCG30798; (ii) successful completion of Certiﬁcate III in Off-site Construction (Joinery—Timber) BCG30200; (iii) a recognition certiﬁcate that a person has worked, or undertaken training, in a calling that includes the skills and knowledge involved in the successful completion of a certiﬁcate mentioned in subparagraph (i) or (ii); (iv) a certiﬁcate of recognition as a qualiﬁed engineering tradesperson under the Tradesmen’s Rights Regulation Act 1946 (Cwlth); (v) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; and (b) a written statement by Construction Training Queensland, or accreditation from the Fire Protection Contractors Registration Board, that a person has competency in both of the following— (i) category IAM—certiﬁcation of installation of ﬁre doors and ﬁre shutters; (ii) category MAN—certiﬁcation of maintenance of ﬁre doors and ﬁre shutters. ‘ (2) For the licence class mentioned in section 1(2)—a qualiﬁcation mentioned in subsection (1)(a). ‘ (3) For the licence class mentioned in section 1(3)—a qualiﬁcation mentioned in subsection (1)(b). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class or work the authority is reasonably satisﬁed is the equivalent of the scope of work for the class.

s 11 55 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 66—FIXED FIRE PUMP SETS LICENCES ‘1 Licence classes ‘ (1) Fixed ﬁre pump sets. ‘ (2) Fixed ﬁre pump sets restricted to carrying out certain work. ‘ (3) Fixed ﬁre pump sets restricted to certiﬁcation of, and preparation of reports about, certain work. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)— (a) carrying out installation and general repair of ﬁxed ﬁre pump sets for a building; and (b) carrying out maintenance of ﬁxed ﬁre pump sets for a building; and (c) certiﬁcation of the installation of ﬁxed ﬁre pump sets for a building under the Standard Building Regulation 1993 ; and (d) preparation of a report for a certiﬁcate or record of maintenance of ﬁxed ﬁre pump sets for a building. ‘ (2) For the licence class mentioned in section 1(2)—carrying out installation and general repair of ﬁxed ﬁre pump sets for a building. ‘ (3) For the licence class mentioned in section 1(3)— (a) carrying out maintenance of ﬁxed ﬁre pump sets for a building; and (b) certiﬁcation of the installation of ﬁxed ﬁre pump sets for a building under the Standard Building Regulation 1993 ; and (c) preparation of a report for a certiﬁcate or record of maintenance of ﬁxed ﬁre pump sets for a building.

s 11 56 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘3 Technical qualiﬁcations ‘ (1) For the licence class mentioned in section 1(1)— (a) either— (i) possession of a plumber’s or water plumber’s licence endorsed ﬁre protection issued by the Plumbers and Drainers Examination and Licensing Board; or (ii) possession of a restricted plumber’s ﬁre protection licence issued by the Plumbers and Drainers Examination and Licensing Board; and (b) a written statement by Construction Training Queensland, or accreditation from the Fire Protection Contractors Registration Board, that a person has competency in all of the following— (i) category IAS–L1—certiﬁcation of installation of pressure maintenance fire pumpsets; (ii) category IAS–L2—certiﬁcation of installation of fire hose reel pumpsets; (iii) category IAS–L3—certiﬁcation of installation of residential fire sprinkler pumpsets; (iv) category IAS–L4—certiﬁcation of installation of fire protection pumpsets; (v) category MAP–L1—certiﬁcation of maintenance of pressure maintenance fire pumpsets; (vi) category MAP–L2—certiﬁcation of maintenance of pre-assembled fire pumpsets; (vii) category MAP–L3—certiﬁcation of maintenance of fire protection fire pumpsets. ‘ (2) For the licence class mentioned in section 1(2)—a qualiﬁcation mentioned in subsection (1)(a). ‘ (3) For the licence class mentioned in section 1(3)—a written statement by Construction Training Queensland, or accreditation from the Fire Protection Contractors Registration Board, that a person has competency in all of the following— (a) category IAS–L1—certiﬁcation of installation of pressure maintenance fire pumpsets;

s 11 57 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (b) category IAS–L2—certiﬁcation of installation of fire hose reel pumpsets; (c) category IAS–L3—certiﬁcation of installation of residential fire sprinkler pumpsets; (d) category IAS–L4—certiﬁcation of installation of fire protection pumpsets; (e) category MAP–L1—certiﬁcation of maintenance of pressure maintenance fire pumpsets; (f) category MAP–L2—certiﬁcation of maintenance of pre-assembled fire pumpsets; (g) category MAP–L3—certiﬁcation of maintenance of fire protection fire pumpsets. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class or work the authority is reasonably satisﬁed is the equivalent of the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 67—FLOOR FINISHING AND COVERING LICENCE ‘1 Licence class ‘Floor ﬁnishing and covering.

s 11 58 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘2 Scope of work ‘ (1) Using ﬂoor sanders and other portable sanders to sand timber, cork and parquetry ﬂoors. ‘ (2) Application of ﬁnishes to timber, cork and parquetry ﬂoors. ‘ (3) Repairing timber ﬂoors. ‘ (4) Fixing or repairing ﬂoating timber ﬂooring. ‘ (5) Fixing or repairing non-structural strip timber ﬂooring. ‘ (6) Fixing or repairing cork ﬂooring. ‘ (7) Fixing or repairing parquetry ﬂooring. ‘ (8) Application or repair of seamless ﬂooring. ‘ (9) Subﬂoor preparation associated with work mentioned in subsections (1) to (8). ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of Certiﬁcate III in Furnishing (Floor Finishing and Covering) (TAFE); (b) a recognition certiﬁcate as qualiﬁed in ﬂoor ﬁnishing and covering; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 59 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 68—FLOOR FINISHING AND COVERING RESTRICTED TO FLOOR SANDING AND FINISHING—TIMBER FLOORS ‘1 Licence class ‘Floor ﬁnishing and covering restricted to ﬂoor sanding and ﬁnishing. ‘2 Scope of work ‘ (1) Using ﬂoor sanders and other portable sanders to sand timber, cork and parquetry ﬂoors; ‘ (2 ) Application of ﬁnishes to timber, cork and parquetry ﬂoors; ‘ (3) Repairing timber ﬂoors; ‘ (4) Subﬂoor preparation associated with work mentioned in subsections (1) to (3). ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of Certiﬁcate III in Furnishing (Floor Finishing and Covering) (TAFE) with the modules ABC853, 861, 864, 957 and 958 or equivalent modules from the modular entry program CNLMF050 (TAFE); (b) a recognition certiﬁcate as qualiﬁed in ﬂoor ﬁnishing and covering; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class.

s 11 60 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 69—FLOOR FINISHING AND COVERING RESTRICTED TO INSTALL FLOATING FLOORING LICENCE ‘1 Licence class ‘Floor ﬁnishing and covering restricted to install ﬂoating ﬂooring. ‘2 Scope of work ‘Fixing or repairing ﬂoating timber ﬂooring and subﬂoor preparation associated with ﬁxing or repairing ﬂoating timber ﬂooring. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of Certiﬁcate III in Furnishing (Floor Finishing and Covering) (TAFE) with the modules ABC861, 863, 864, 957 and 958 or equivalent modules from the modular entry program CNLMF050 (TAFE); (b) a recognition certiﬁcate as qualiﬁed in ﬂoor ﬁnishing and covering; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class.

s 11 61 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 70—FLOOR FINISHING AND COVERING RESTRICTED TO INSTALL STRIP FLOORING (NON–STRUCTURAL) LICENCE ‘1 Licence class ‘Floor ﬁnishing and covering restricted to install strip ﬂooring (non-structural). ‘2 Scope of work ‘Fixing or repairing non-structural strip timber ﬂooring and subﬂoor preparation associated with ﬁxing or repairing non-structural strip timber ﬂooring. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of Certiﬁcate III in Furnishing (Floor Finishing and Covering) (TAFE) with the modules ABC861, 864, 865, 957 and 958 or equivalent modules from the modular entry program CNLMF050 (TAFE); (b) a recognition certiﬁcate as qualiﬁed in ﬂoor ﬁnishing and covering; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation.

s 11 62 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 71—FLOOR FINISHING AND COVERING RESTRICTED TO SEAMLESS FLOORING LICENCE ‘1 Licence class ‘Floor ﬁnishing and covering restricted to seamless ﬂooring. ‘2 Scope of work ‘Application or repair of seamless ﬂooring and subﬂoor preparation associated with the application or repairing of seamless ﬂooring. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of Certiﬁcate III in Furnishing (Floor Finishing and Covering) (TAFE) with the modules ABC853, 861, 957 and 958 or equivalent modules from the modular entry program CNLMF050 (TAFE); (b) a recognition certiﬁcate as qualiﬁed in ﬂoor ﬁnishing and covering; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation.

s 11 63 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 72—FLOOR FINISHING AND COVERING RESTRICTED TO INSTALL CORK FLOORING LICENCE ‘1 Licence class ‘Floor ﬁnishing and covering restricted to install cork ﬂooring. ‘2 Scope of work ‘Fixing or repairing cork ﬂooring and subﬂoor preparation associated with ﬁxing or repairing cork ﬂooring. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of Certiﬁcate III in Furnishing (Floor Finishing and Covering) (TAFE) with the modules ABC853, 861, 957 and 958 or equivalent modules from the modular entry program CNLMF050 (TAFE); (b) a recognition certiﬁcate as qualiﬁed in ﬂoor ﬁnishing and covering; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation.

s 11 64 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 73—FLOOR FINISHING AND COVERING RESTRICTED TO INSTALL PARQUETRY FLOORING LICENCE ‘1 Licence class ‘Floor ﬁnishing and covering restricted to install parquetry ﬂooring. ‘2 Scope of work ‘Fixing or repairing parquetry ﬂooring and subﬂoor preparation associated with ﬁxing or repair of parquetry ﬂooring. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of Certiﬁcate III in Furnishing (Floor Finishing and Covering) (TAFE) with the modules ABC855, 856, 861, 957 and 958 or equivalent modules from the modular entry program CNLMF050 (TAFE); (b) a recognition certiﬁcate as qualiﬁed in ﬂoor ﬁnishing and covering; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation.

s 11 65 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 74—INSULATING RESTRICTED TO RESIDENTIAL INSULATION LICENCE ‘1 Licence class ‘Insulating restricted to residential insulation. ‘2 Scope of work ‘Preparation and installation of insulation materials, by physical or mechanical means, for the purpose of acoustic and thermal control in residential situations. ‘3 Technical qualiﬁcations ‘A qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 66 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 75—KITCHEN, BATHROOM AND LAUNDRY INSTALLATIONS LICENCE ‘1 Licence class ‘Kitchen, bathroom and laundry installations. ‘2 Scope of work ‘ (1) On-site installation of kitchen, bathroom and laundry cabinets and associated products. ‘ (2) On-site refurbishment, restoration or repair of kitchen, bathroom or laundry cabinets. ‘ (3) Engagement and supervision of appropriate licence holders involved in the installation, refurbishment, restoration or repair of kitchen, bathroom and laundry cabinets. ‘ (4) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence or work that affects a part of the building which is loadbearing or a structural member. ‘3 Technical qualiﬁcations ‘Successful completion of OL1001F Cabinet Installation Trade Coordination and any 1 of the following— (a) successful completion of Certiﬁcate III in General Construction (Carpentry—Framework/Formwork/Finishing) BCG30798; (b) successful completion of Certiﬁcate III in Off-site Construction (Joinery—Timber) BCG30200; (c) successful completion of Certiﬁcate III in Off-site Construction (Shopﬁtting) BCG30100; (d) successful completion of Certiﬁcate III in Furnishing (Cabinet-making) CCN0180; (e) a recognition certiﬁcate as a qualiﬁed cabinet-maker, carpenter, carpenter and joiner or shopﬁtter;

s 11 67 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (f) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; (g) a current licence under the QueenslandBuildingServicesAuthorityAct1991 in the classes of carpentry or carpentry restricted to internal ﬁnishes. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 76—METAL FABRICATING RESTRICTED TO NON–STRUCTURAL METAL FABRICATING LICENCE ‘1 Licence class ‘Metal fabricating restricted to non-structural metal fabricating. ‘2 Scope of work ‘Preparation, fabrication or erection of non-structural metal components in building work. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of an apprenticeship as an engineering tradesperson in fabrication;

s 11 68 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (b) a certiﬁcate of recognition as a qualiﬁed engineering tradesperson under the Tradesmen’s Rights Regulation Act 1946 (Cwlth); (c) a recognition certiﬁcate as a qualiﬁed engineering tradesperson; (d) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 77—METAL FABRICATING RESTRICTED TO SHEDS, GARAGES AND CARPORTS LICENCE ‘1 Licence class ‘Metal fabricating restricted to sheds, garages and carports. ‘2 Scope of work ‘Preparation, fabrication or erection of the metal components for sheds, garages and carports and the like, which are classiﬁed as non-habitable buildings, class 10a, under the Building Code of Australia.

s 11 69 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘3 Technical qualiﬁcations ‘A qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 78—PAINTING RESTRICTED TO SPECIAL FINISHES LICENCE ‘1 Licence class ‘Painting restricted to special ﬁnishes. ‘2 Scope of work ‘The application of wallpaper and other special ﬁnishes that form a ﬁlm when dry for protective, decorative or technical purposes. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a painting and decorating apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed painter and decorator;

s 11 70 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 79—PAINTING RESTRICTED TO NEW DOMESTIC BUILDINGS LICENCE ‘1 Licence class ‘Painting restricted to new domestic buildings. ‘2 Scope of work ‘Surface preparation and application of paint or another substance that forms a ﬁlm when dry for protective, decorative or technical purposes on new domestic building work. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a painting and decorating apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed painter and decorator;

s 11 71 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 80—PAINTING RESTRICTED TO REPAINTING DOMESTIC BUILDINGS LICENCE ‘1 Licence class ‘Painting restricted to repainting domestic buildings. ‘2 Scope of work ‘Surface preparation and application of paint or another substance that forms a ﬁlm when dry for protective, decorative or technical purposes on existing domestic building work. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a painting and decorating apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed painter and decorator;

s 11 72 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 81—PAINTING RESTRICTED TO ROOF PAINTING LICENCE ‘1 Licence class ‘Painting restricted to roof painting. ‘2 Scope of work ‘Cleaning roofs and application to roofs of paint or another substance that forms a ﬁlm when dry for protective, decorative or technical purposes. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a painting and decorating apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed painter and decorator; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence.

s 11 73 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 82—PEST CONTROLLING RESTRICTED TO TERMITE BARRIER INSTALLATION LICENCES ‘1 Licence classes ‘ (1) Pest controlling restricted to termite barrier installation. ‘ (2) Pest controlling restricted to termite barrier installation without chemicals. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)—installation of material or a system designed for the prevention of termite infestation including material or a system where application of a chemical forms part of the material or a system. ‘ (2) For the licence class mentioned in section 1(2)—installation of material or a system designed for the prevention of termite infestation other than material or a system where application of a chemical forms part of the material or a system. ‘3 Technical qualiﬁcation ‘ (1) For the licence class mentioned in section 1(1)—

s 11 74 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (a) certiﬁcation by the manufacturer or supplier of material or a system to be used by a holder of the licence that the holder has satisfactorily completed a course about the installation of the material or system; and (b) possession of a licence under the HealthAct1937 , part 4, division 7. 3 ‘ (2) For the licence class mentioned in section 1(2)—certiﬁcation by the manufacturer or supplier of material or a system to be used by a holder of the licence that the holder has satisfactorily completed a course about the installation of the material or system. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 83—PLUMBING AND DRAINING RESTRICTED TO PLUMBING LICENCE ‘1 Licence class ‘Plumbing and draining restricted to plumbing. ‘2 Scope of work ‘ (1) Installation of sanitary, waste disposal and water supply ﬁxtures. ‘ (2) Fabrication, installation of pipework to ﬁxtures. ‘ (3) Testing sanitary, waste disposal and water supply installations. 3 Health Act 1937 , part 4 (Drugs and other articles), division 7 (Pest control operators)

s 11 75 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘ (4) Installation of plumbing work and pipe ﬁtting for steam, gas and air vacuum equipment. ‘ (5) Installation of ventilation and heating equipment. ‘ (6) Installation of metal rooﬁng and wall sheeting. ‘ (7) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘A plumber’s licence issued by the Plumbers and Drainers Examination and Licensing Board. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 84—PLUMBING AND DRAINING RESTRICTED TO DRAINING LICENCE ‘1 Licence class ‘Plumbing and draining restricted to draining. ‘2 Scope of work ‘ (1) Installation of drainage systems for above and below ground drains. ‘ (2) Laying below ground unventilated branch drains (pipes and ﬁttings).

s 11 76 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘ (3) Installation of ﬂoor waste gully installation (pipes and ﬁttings). ‘ (4) Installation and testing of property drains. ‘ (5) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘A drainer’s licence issued by the Plumbers and Drainers Examination and Licensing Board. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 85—PLUMBING AND DRAINING RESTRICTED TO ROOFING AND WALL CLADDING LICENCE ‘1 Licence class ‘Plumbing and draining restricted to rooﬁng and wall cladding. ‘2 Scope of work ‘ (1) Installation of metal sheet rooﬁng and cladding and components. ‘ (2) Designing, fabrication and installation of ﬂashings to roofs, walls, pipe penetrations and roof ventilators or skylights. ‘ (3) Installation of fascias, barges, gutters and downpipes.

s 11 77 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘ (4) Installation of concealed guttering. ‘ (5) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a plumbing and draining apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed plumber and drainer; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 86—PLUMBING AND DRAINING RESTRICTED TO SKYLIGHT AND VENTILATOR INSTALLATION LICENCE ‘1 Licence class ‘Plumbing and draining restricted to skylight and ventilator installation.

s 11 78 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘2 Scope of work ‘The preparation and installation of skylights and roof ventilators to tile and sheet roofs. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a plumbing and draining apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed plumber and drainer; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 87—PLUMBING AND DRAINING RESTRICTED TO TANKS—WATER SUPPLY LICENCE ‘1 Licence class ‘Plumbing and drainage restricted to tanks (water supply).

s 11 79 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘2 Scope of work ‘ (1) Fabrication and installation of tanks, equipment and components for water storage and water supply to a building. ‘ (2) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a plumbing and draining apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed plumber and drainer; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 88—PLUMBING AND DRAINING RESTRICTED TO URBAN IRRIGATION LICENCE ‘1 Licence class ‘Plumbing and draining restricted to urban irrigation.

s 11 80 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘2 Scope of work ‘Selection and installation of urban irrigation equipment for landscaping. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of Urban Irrigation Installers course CTQ005 (TAFE); (b) successful completion of a plumbing and draining apprenticeship; (c) a recognition certiﬁcate as a qualiﬁed plumber and drainer. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 89—PLUMBING AND DRAINING RESTRICTED TO FASCIAS, BARGES, GUTTERS AND DOWNPIPES LICENCE ‘1 Licence class ‘Plumbing and draining restricted to fascias, barges, gutters and downpipes.

s 11 81 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘2 Scope of work ‘Installation or repair of fascias, barges, gutters and downpipes. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a plumbing and draining apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed plumber and drainer; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 90—PLUMBING AND DRAINING RESTRICTED TO WALL CLADDING LICENCE ‘1 Licence class ‘Plumbing and draining restricted to wall cladding. ‘2 Scope of work ‘The preparation of existing framed walls for the installation of cladding and the ﬁxing of boards, sheets or sidings to external walls.

s 11 82 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘3 Technical qualiﬁcations ‘A qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 91—PLASTERING DRYWALL RESTRICTED TO CORNICE FIXING LICENCE ‘1 Licence class ‘Plastering drywall restricted to cornice ﬁxing. ‘2 Scope of work ‘The ﬁxing of plaster, ﬁbrous or composite non-ﬁre-rated sheet cornices. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a plastering (wall and ceiling ﬁxing) apprenticeship; (b) a recognition certiﬁcate as a plasterer (wall and ceiling ﬁxing); (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence.

s 11 83 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 92—PLASTERING DRYWALL RESTRICTED TO PARTITION INSTALLATION LICENCE ‘1 Licence class ‘Plastering drywall restricted to partition installation. ‘2 Scope of work ‘Setting out and installation of ﬁxed or demountable non-ﬁre-rated wall systems but excluding work that is cast or laid. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a plastering (wall and ceiling ﬁxing) apprenticeship; (b) a recognition certiﬁcate as a plasterer (wall and ceiling ﬁxing); (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation.

s 11 84 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 93—PLASTERING DRYWALL RESTRICTED TO PLASTER SETTING LICENCE ‘1 Licence class ‘Plastering drywall restricted to plaster setting. ‘2 Scope of work ‘Stopping, setting or scrimming of plaster, ﬁbrous or composite non-ﬁre-rated sheet linings. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a plastering (wall and ceiling ﬁxing) apprenticeship; (b) a recognition certiﬁcate as a plasterer (wall and ceiling ﬁxing); (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class.

s 11 85 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 94—PLASTERING DRYWALL RESTRICTED TO SUSPENDED CEILING FIXING LICENCE ‘1 Licence class ‘Plastering drywall restricted to suspended ceiling ﬁxing. ‘2 Scope of work ‘Setting out and installation of ﬁxed or demountable non-ﬁre-rated ceiling systems but excluding work that is cast or laid. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a plastering (wall and ceiling ﬁxing) apprenticeship; (b) a recognition certiﬁcate as a plasterer (wall and ceiling ﬁxing); (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 86 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 95—PLASTERING DRYWALL RESTRICTED TO WALLBOARD FIXING LICENCE ‘1 Licence class ‘Plastering drywall restricted to wallboard ﬁxing. ‘2 Scope of work ‘Fixing of plaster, ﬁbrous or composite non-ﬁre-rated sheet linings, including framing and battening. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a plastering (wall and ceiling ﬁxing) apprenticeship; (b) a recognition certiﬁcate as a plasterer (wall and ceiling ﬁxing); (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 87 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 96—REFRIGERATION, AIRCONDITIONING AND MECHANICAL SERVICES RESTRICTED TO DUCTING MANUFACTURE AND INSTALLATION LICENCE ‘1 Licence class ‘Refrigeration, airconditioning and mechanical services restricted to ducting manufacture and installation. ‘2 Scope of work ‘Designing, fabrication and installation of ducting and all other metal products associated with refrigerative airconditioning, mechanical ventilation or air-handling systems. ‘3 Technical qualiﬁcations ‘Either— (a) successful completion of a sheet metal worker’s apprenticeship; or (b) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 88 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 97—REFRIGERATION, AIRCONDITIONING AND MECHANICAL SERVICES RESTRICTED TO MULTIPACKAGED RESIDENTIAL AIRCONDITIONING EQUIPMENT AND PLANT LICENCE ‘1 Licence class ‘Refrigeration, airconditioning and mechanical services restricted to multipackaged residential airconditioning equipment and plant. ‘2 Scope of work ‘Installation, commissioning, servicing or repairing split type refrigeration airconditioning units requiring any form of ﬁeld or site work to the system. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) completion of an apprenticeship as a refrigeration, airconditioning and engineering tradesperson; (b) a certiﬁcate of recognition under the Tradesmen’s Rights Regulation Act 1946 (Cwlth); (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class.

s 11 89 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 98—REFRIGERATION, AIRCONDITIONING AND MECHANICAL SERVICES RESTRICTED TO RESIDENTIAL EVAPORATIVE COOLING EQUIPMENT LICENCE ‘1 Licence class ‘Refrigeration, airconditioning and mechanical services restricted to residential evaporative cooling equipment. ‘2 Scope of work ‘Installation, commissioning, servicing or repairing evaporative (water) cooling systems intended for residential applications. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) completion of an apprenticeship as a refrigeration, airconditioning and engineering tradesperson; (b) a certiﬁcate of recognition under the Tradesmen’s Rights Regulation Act 1946 (Cwlth); (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class.

s 11 90 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 99—REFRIGERATION, AIRCONDITIONING AND MECHANICAL SERVICES RESTRICTED TO SELF-CONTAINED WINDOW PACKAGE RESIDENTIAL AIRCONDITIONING INSTALLATION LICENCE ‘1 Licence class ‘Refrigeration, airconditioning and mechanical services restricted to self-contained window packaged residential airconditioning installation. ‘2 Scope of work ‘ (1) Installation, in a window or wall, of self-contained window packaged residential airconditioning that operates on electricity from an existing power outlet, and using mounting brackets supplied by the manufacturer or supplier of the airconditioning. ‘( 2) Installation of condensate drainage line. ‘ (3) Servicing removable ﬁlters and units. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) completion of an apprenticeship as a refrigeration, airconditioning and engineering tradesperson; (b) a certiﬁcate of recognition under the Tradesmen’s Rights Regulation Act 1946 (Cwlth); (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence.

s 11 91 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 100—ROOF TILING RESTRICTED TO ROOF TILE MAINTENANCE LICENCE ‘1 Licence class ‘Roof tiling restricted to roof tile maintenance. ‘2 Scope of work ‘Repairing and replacing existing tiles with similar materials and rebedding, repointing and recoating existing tile roofs. ‘3 Technical qualiﬁcations ‘Any 1 of the following— (a) successful completion of a roof tiling apprenticeship; (b) a recognition certiﬁcate as a qualiﬁed roof tiler; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation.

s 11 92 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 101—SITE CLASSIFIER LICENCES ‘1 Licence classes ‘ (1) Site classiﬁer. ‘ (2) Site classiﬁer excluding on-site domestic waste water management. ‘2 Scope of work ‘ (1) For the licence class mentioned in section 1(1)— (a) sampling, testing and assessing soils on building sites; and (b) classiﬁcation of building sites in accordance with the relevant Australian Standard through the interpretation of site and laboratory information; and (c) preparing plans, speciﬁcations and documents associated with on-site domestic waste water management. ‘ (2) For the licence class mentioned in section 1(2)— (a) sampling, testing and assessing soils on building sites; and (b) classiﬁcation of building sites in accordance with the relevant Australian Standard through the interpretation of site and laboratory information. ‘3 Technical qualiﬁcations ‘ (1) For the licence class mentioned in section 1(1)— (a) any 1 of the following—

s 11 93 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (i) successful completion of— (A) a traineeship in construction—materials (soil testing); and (B) the module ‘classify soil’ through a registered training organisation; (ii) a recognition certiﬁcate as being qualiﬁed in materials (soil testing) and successful completion of the module ‘classify soil’ through a registered training organisation; (iii) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; and (b) successful completion of Site Assessment and Design Course CNQ12 (TAFE) or a course the authority considers is at least equivalent to the CNQ12 course. ‘ (2) For the licence class mentioned in section 1(2)—any 1 of the following— (a) successful completion of— (i) a traineeship in construction—materials (soil testing); and (ii) the module ‘classify soil’ through a registered training organisation; (b) a recognition certiﬁcate as being qualiﬁed in materials (soil testing) and successful completion of the module ‘classify soil’ through a registered training organisation; (c) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience with the scope of work for the class.

s 11 94 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 102—SPECIALISED CONTRACTING–SCREW-IN FOUNDATIONS LICENCE ‘1 Licence class ‘Specialised contracting—screw-in foundations. ‘2 Scope of work ‘ (1) Site preparation for installation of screw-in foundations. ‘ (2) Installation of screw-in foundations using machinery or plant. ‘3 Technical qualiﬁcations ‘Certiﬁcation by the manufacturer or supplier of a product or system to be used by a holder of the licence that the holder has satisfactorily completed a course about the installation of the product or system. ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 95 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 103—SPECIALISED CONTRACTING—SOLID FUEL HEATER INSTALLATION LICENCE ‘1 Licence class ‘Specialised contracting—solid fuel heater installation. ‘2 Scope of work ‘Installation of solid fuel heaters. ‘3 Technical qualiﬁcations ‘Successful completion of the course titled ‘Installation of Solid Fuel Heater’ (TAFE). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 104—STRUCTURAL LANDSCAPING RESTRICTED TO FENCES LICENCE ‘1 Licence class ‘Structural landscaping restricted to fences. ‘2 Scope of work ‘Fabrication, site preparation and erection of fences and gates.

s 11 96 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘3 Technical qualiﬁcations ‘Either— (a) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; or (b) a recognition certiﬁcate that a person has worked, or undertaken training, in a calling that includes the skills and knowledge required to obtain a qualiﬁcation or statement of attainment mentioned in paragraph (a). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 105—STRUCTURAL LANDSCAPING RESTRICTED TO RETAINING WALLS LICENCE ‘1 Licence class ‘Structural landscaping restricted to retaining walls. ‘2 Scope of work ‘Fabrication, preparation and erection of retaining walls.

s 11 97 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘3 Technical qualiﬁcations ‘Either— (a) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; or (b) a recognition certiﬁcate that a person has worked, or undertaken training, in a calling that includes the skills and knowledge required to obtain a qualiﬁcation or statement of attainment mentioned in paragraph (a). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 106—SWIMMING POOL AND SPA CONSTRUCTION RESTRICTED TO FINISHES LICENCE ‘1 Licence class ‘Swimming pool and spa construction restricted to ﬁnishes. ‘2 Scope of work ‘Application to the surface of a swimming pool or spa of exposed aggregate or other ﬁnishes of either natural or synthetic material that is trowelled, rolled or applied by brush.

s 11 98 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘3 Technical qualiﬁcations ‘Either— (a) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; or (b) a recognition certiﬁcate that a person has worked, or undertaken training, in a calling that includes the skills and knowledge required to obtain a qualiﬁcation or statement of attainment mentioned in paragraph (a). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 107—SWIMMING POOL AND SPA CONSTRUCTION RESTRICTED TO CONCRETE LICENCE ‘1 Licence class ‘Swimming pool and spa construction restricted to concrete. ‘2 Scope of work ‘ (1) Earthworks and drainage associated with concrete swimming pool and spa installation and construction. ‘ (2) Placement and ﬁxing of reinforcement.

s 11 99 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘ (3) Formwork to edges to deﬁne a swimming pool or spa shape or form not exceeding 1.5 m above ground level. ‘ (4) Placement and ﬁnishing of concrete to provide a shape or form for a swimming pool or spa. ‘ (5) Ancillary pipework including general ﬁltration, sanitation, water chemistry and basic hydraulics. ‘(6) Minor landscaping works, including fencing required by statutory requirements, paving and tiling. ‘ (7) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Either— (a) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; or (b) a recognition certiﬁcate that a person has worked, or undertaken training, in a calling that includes the skills and knowledge required to obtain a qualiﬁcation or statement of attainment mentioned in paragraph (a). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.

s 11 100 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘PART 108—SWIMMING POOL AND SPA CONSTRUCTION RESTRICTED TO FIBREGLASS LICENCE ‘1 Licence class ‘Swimming pool and spa construction restricted to ﬁbreglass. ‘2 Scope of work ‘ (1) Earthworks and drainage associated with ﬁbreglass swimming pool and spa installation and construction. ‘ (2) Placement, packing, ﬁlling and levelling of ﬁbreglass swimming pool and spa shells. ‘ (3) Ancillary pipework including general ﬁltration, sanitation, water chemistry and basic hydraulics. ‘ (4) Minor landscaping works, including fencing required by statutory requirements, paving and tiling. ‘ (5) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Either— (a) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; or (b) a recognition certiﬁcate that a person has worked, or undertaken training, in a calling that includes the skills and knowledge required to obtain a qualiﬁcation or statement of attainment mentioned in paragraph (a). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation.

s 11 101 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 109—SWIMMING POOL AND SPA CONSTRUCTION RESTRICTED TO POOL MAINTENANCE AND REPAIRS LICENCE ‘1 Licence class ‘Swimming pool and spa construction restricted to pool maintenance and repairs. ‘2 Scope of work ‘ (1) Swimming pool and spa maintenance and repairs associated with— (a) the framework of a swimming pool or spa wall; (b) the synthetic liner of a swimming pool or spa; (c) associated pipework including general ﬁltration, sanitation, water chemistry and basic hydraulics. ‘ (2) Minor landscaping works, including fencing required by statutory requirements, paving and tiling. ‘ (3) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Either— (a) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; or

s 11 102 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 (b) a recognition certiﬁcate that a person has worked, or undertaken training, in a calling that includes the skills and knowledge required to obtain a qualiﬁcation or statement of attainment mentioned in paragraph (a). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 110—SWIMMING POOL AND SPA CONSTRUCTION RESTRICTED TO PREFABRICATED OR PACKAGED PRODUCTS LICENCE ‘1 Licence class ‘Swimming pool and spa construction restricted to prefabricated or packaged products. ‘2 Scope of work ‘ (1) Earthworks and drainage associated with prefabricated or packaged swimming pool and spa installation and construction. ‘ (2) Fabrication and erection of framework for swimming pool and spa walls. ‘ (3) Placement, packing, ﬁlling and levelling of prefabricated units. ‘ (4) Installation of synthetic swimming pool and spa liners.

s 11 103 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘ (5) Ancillary pipework including general ﬁltration, sanitation, water chemistry and basic hydraulics. ‘ (6) Minor landscaping works, including fencing required by statutory requirements, paving and tiling. ‘ (7) Work of another class in connection with work in this class, but not work that may be carried out only by the holder of an occupational licence. ‘3 Technical qualiﬁcations ‘Either— (a) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; or (b) a recognition certiﬁcate that a person has worked, or undertaken training, in a calling that includes the skills and knowledge required to obtain a qualiﬁcation or statement of attainment mentioned in paragraph (a). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 111—WATERPROOFING RESTRICTED TO COMMERCIAL WATERPROOFING LICENCE ‘1 Licence class ‘Waterprooﬁng restricted to commercial waterprooﬁng.

s 11 104 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘2 Scope of work ‘The preparation of surfaces and the application or repair of a product or system speciﬁcally for the purpose of preventing moisture penetration in commercial applications. ‘3 Technical qualiﬁcations ‘Either— (a) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; or (b) a recognition certiﬁcate that a person has worked, or undertaken training, in a calling that includes the skills and knowledge required to obtain a qualiﬁcation or statement of attainment mentioned in paragraph (a). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies. ‘PART 112—WATERPROOFING RESTRICTED TO RESIDENTIAL WATERPROOFING LICENCE ‘1 Licence class ‘Waterprooﬁng restricted to residential waterprooﬁng.

s 11 105 s 11 Queensland Building Services Authority Amendment No. 190, 2002 Regulation (No. 2) 2002 ‘2 Scope of work ‘The preparation of surfaces and the application or repair of a product or system speciﬁcally for the purpose of preventing moisture penetration in residential applications. ‘3 Technical qualiﬁcations ‘Either— (a) a qualiﬁcation or statement of attainment issued by an approved authority for the class of licence; or (b) a recognition certiﬁcate that a person has worked, or undertaken training, in a calling that includes the skills and knowledge required to obtain a qualiﬁcation or statement of attainment mentioned in paragraph (a). ‘4 Managerial qualiﬁcations ‘An approved managerial qualiﬁcation. ‘5 Experience requirements ‘Two years practical experience in the scope of work for the class. ‘6 Financial requirements ‘The relevant ﬁnancial requirements set out in the board’s policies.’. ENDNOTES 1. Made by the Governor in Council on 1 August 2002. 2. Notiﬁed in the gazette on 2 August 2002. 3. Laid before the Legislative Assembly on . . . 4. The administering agency is the Department of Housing. © State of Queensland 2002