Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2006 (No. 1) (Cth)
Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2006 (No. 1)
I, JAMES ERIC LLOYD, Minister for Local Government, Territories and Roads, make this Determination under subsection 13D (2) of the Motor Vehicle Standards Act 1989.
Dated: 19 June 2006
[signed]
JIM LLOYD
Contents
Page
Name of Determination 2
Commencement 2
Revocation of the Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2002 (2). 2
Definitions 2
Vehicle inspection certificate 3
Schedule 1Vehicle inspection certificate 4
1 Name of Determination
This Determination is the Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2006 (No. 1).
2 Commencement
This Determination commences on the day after registration on the Federal Register of Legislative Instruments.
Revocation of the Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2002 (2).
Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2002 (2) is revoked.
Note: The Motor Vehicle Standards (Used Import Vehicle Report) Determination 2002 (2) was made by the Parliamentary Secretary to the Minister for Transport and Regional Services on 12 December 2002 and notified in the Gazette on 18 December 2002.
4 Definitions
(1) In this Determination:
Act means the Motor Vehicle Standards Act 1989.
ADR means the Australian Design Rules.
Full bump means when the suspension is fully compressed.
Plate location means the location of the Used Import Plate as required by the Motor Vehicle Standards (Placement of Used Import Plates) Determination 2004 (No.1) made under s13B of the Act in accordance with the grid locations specified in the Vehicle Inspection Manual as approved by the Administrator of Vehicle Standards on 9 December 2002.
vehicle identification number (VIN), for a vehicle, means a number:
(a)corresponding to the vehicle identification number of the vehicle; and
(b)stated on a used import plate that identifies the vehicle.
VIN location means the position on the vehicle, of the Vehicle Identification Number as required by clause 5.1 of ADR 61/02 in accordance with the grid locations specified in the Vehicle Inspection Manual as approved by the Administrator of Vehicle Standards on 9 December 2002.
(2) Unless the contrary intention appears, a word or expression that is used in this Determination and in the Motor Vehicle Standards Regulations 1989 has the same meaning in this Determination as it has in those Regulations.
Note 1 The following terms are defined in the Act:
· registered automotive workshop
· used imported vehicle.
Note 2 The following terms are defined in the Motor Vehicle Standards Regulations 1989:
· Australian Design Rules
· make
· model
· RAW
· Register of Specialist and Enthusiast Vehicles
· RVCS participant number (defined in regulation 39)
· vehicle category
· vehicle inspection signatory (defined in regulation 39)
Note 1: The following are defined terms in the ADRs
·B Double
·Gross Vehicle Mass
·Gross Combination Mass
·Ground Clearance
·Net Engine Power (NEP)
·Overall width
·Road Train
·Tare Mass
·Wheelbase
5 Vehicle inspection certificate
For subsection 13D (2) of the Act, a report in relation to a used imported vehicle (to be known as a Vehicle Inspection Certificate) is to be in the form, and contain the information, set out in Schedule 1.
Schedule 1 Vehicle inspection certificate
(section 5)
|
Application Reference
RAWS Participant ID No Your Document Reference No
Replacement Form
If applicable – to correct a previously Replaced Form Document Reference No.
submitted form:
Vehicle Details
| VIN | Model | ||
| Make | Model Code | ||
| Vehicle Category | VIN location | - | - |
| Build Date (MM/YYYY) | Used Import Plate Location | - | - |
| SEVS Entry Number | RAWS Schedule No. | ||
| Import Approval No |
Variant Details
| Variant Name | Tare Mass | ||||||
| Gross Vehicle Mass | Gross Combination Mass | ||||||
| Seating Options | Axle Code | Braked | Un-Braked | ||||
| Max Towing Mass | |||||||
| Number of Doors | Side | Rear | B-Double Capable | Road Train Capable | |||
Engine Details
| Model | Number | ||||||||||||
| Engine Number location | |||||||||||||
| Capacity (cc) | Configuration | Motive Power | NEP (kW) | NEP (rpm) | Fuel Injection/ Carburettor | Strokes & cycle | Induc-tion | ||||||
Service Brakes
| Brake System | Front | Rear | |||||
| Actuation Type | Power Assisted? | Type | Nominal Diameter (mm) | Nominal Width (mm) | Type | Nominal Diameter (mm) | Nominal Width (mm) |
Transmission
Transmission Forward Forward Gears
Tyre and Rim Information
| Tyre Designation | Rim Size and Profile | Rim Offset (mm) | Wheel Track (mm) |
| Front | |||
| Rear |
Suspension Data Major Dimensions
| Wheel Centre to top of wheel arch | Unladen | Full bump | Total Length (mm) | Overall Width (mm) | Height (mm) | Wheel-Base (mm) | Ground Clearance (mm) |
| Front (mm) | |||||||
| Rear (mm) |
Equipment Affecting ADR Compliance
| Air Conditioning | Antilock Brakes | Power Windows | Power Mirrors |
| Drivers Airbag | Passengers Airbag | Central locking | Other |
Axle Load Ratings
| Axle No | First front axle | Second front axle | First rear axle | Second rear axle | Third rear axle |
| Axle Load Rating (kg) for heaviest variant |
Remarks
| Incoming Vehicle Inspection Report | Document Reference No |
| Consumer Information Notice | Document Reference No |
| Completed Vehicle Report | Document Reference No |
EVIDENCE TO DEMONSTRATE THAT THIS VEHICLE MEETS THE REQUIREMENTS
| ADR Number | Sample Evidence Document Reference | Evidence Type | New Evidence | Specific Evidence Document Reference |
Declaration
This declaration must be made before this Vehicle Inspection Certificate is transmitted to DOTARS.
|
|
I (name of Vehicle Inspection Signatory)
certify that I have seen and inspected the vehicle identified in this Certificate and confirm that it has been modified in accordance with the evidence set out in this Certificate and in accordance with the Motor Vehicle Standards (Approval to Place Used Import Plates) Guidelines 2006 (No. 1).
Cross to indicate agreement with the above statement.
0
0
0