Ministerial Standard 313 (Cth)

1987 No. 40*1* STANDARD UNDER THE RADIOCOMMUNICATIONS ACT 1983

*1* Notified in the Commonwealth of Australia Gazette on 12 March 1987.

1987 No. 40 STANDARD UNDER THE RADIOCOMMUNICATIONS ACT 1983 - REG 1 
Citation 


  1. This standard may be cited as "Ministerial Standard 313".

1987 No. 40 STANDARD UNDER THE RADIOCOMMUNICATIONS ACT 1983 - REG 2 
Commencement 


  2. This standard shall come into operation on 16 March 1987.

1987 No. 40 STANDARD UNDER THE RADIOCOMMUNICATIONS ACT 1983 - REG 3 
Devices to which this standard applies 


  3. This standard applies to cellular subscriber units as defined in section
1.3 of IS-19 of Telecom Specification TPH 1666.

1987 No. 40 STANDARD UNDER THE RADIOCOMMUNICATIONS ACT 1983 - REG 4 
Adoption of matter contained in TPH 1666 approved by Telecom Australia 


  4. (1) In accordance with sub-section 9 (11) of the Radiocommunications Act
1983, this standard adopts those parts of "TPH 1666: CMTS Cellular Mobile
Telephone System-Air Interface Compatibility Specification" approved by the
Australian Telecommunications Commission (Telecom) and published in January
1986, as are set out in item 1 of the schedule and modified in accordance with
sub-clause 5 (2).
  (2) The matter adopted by this standard is amended by substituting "-10
degrees C" for "-30 degrees " wherever it occurs.

1987 No. 40 STANDARD UNDER THE RADIOCOMMUNICATIONS ACT 1983 - REG 5 
Equipment markings 


  5. (1) Subject to sub-clause 5 (3), a cellular subscriber unit to which this
standard applies shall display:

  (a)  the name of its manufacturer;

  (b)  the name of the country of its manufacture;

  (c)  its type or model designation;

  (d)  its equipment serial number; and

  (e)  a compliance statement in the form set out in item 2 of the schedule-

      (i)  indicating that the cellular subscriber unit complies with this

standard; and

     (ii)  citing the Department of Communications type approval number shown
on the compliance statement certificate issued in respect of the cellular
subscriber unit under section 12 of the Radiocommunications Act 1983.
  (2) A statement or marking displayed on a cellular subscriber unit to which
this standard applies in accordance with sub-clause 5 (1) shall be clearly
visible, indelible, tamper proof and unable to be transferred either in whole
or in part from the cellular subscriber unit.
  (3) The requirement of paragraph 5 (1) (e) does not apply to a cellular
subscriber unit unless the importer, manufacturer or supplier of the cellular
subscriber unit, as the case may be, has been issued with a compliance
statement certificate in respect of the cellular subscriber unit.

1987 No. 40 STANDARD UNDER THE RADIOCOMMUNICATIONS ACT 1983 - REG 6 
Adjustment mechanisms 


  6. A cellular subscriber unit to which this standard applies shall not
incorporate adjustment mechanisms accessible without tools, being mechanisms
which would enable operation of the cellular subscriber unit otherwise than in
accordance with this standard.

1987 No. 40 STANDARD UNDER THE RADIOCOMMUNICATIONS ACT 1983 - SCHEDULE 
SCH

                                    SCHEDULE

Item 1    MATTER ADOPTED BY THIS STANDARD. This standard adopts

          those sections of IS-19 of "TPH 1666: CMTS Cellular

          Mobile Telephone System-Air Interface Compatibility

          Specification" as are set out in Column 1 of the

          following table, Column 2 of which specifies opposite each

          section the subject matter to which it relates:               Clause
4 

          COLUMN 1     COLUMN 2

          Section      Subject matter

          1.3.1        Channel Numbering and Frequencies

          2.1          Frequency Requirements

          2.2.1        Type of Modulation

          2.3.1        RF Sensitivity

          2.3.2        Adjacent and Alternate Channel

                       Desensitization

          2.3.3        Intermodulation Spurious Response Attenuation

          2.3.4        Protection Against Spurious-Response

                       Interference

          2.4          Conducted Spurious Emission

          2.5          Radiated Spurious Emission

          3.1          Frequency Requirements

          3.2.1        RF Power Output

          3.2.3        Carrier-On State

          3.3.2.3      Modulation Deviation Limiting

          3.4.1        Spectrum Noise Suppression

          3.4.2        Harmonic and Spurious Emissions (Conducted)

          4.1          Temperature and Power Supply Voltage

          5            Standard Radiated Signal Measurement

                       Procedure

          6            Standard Test Conditions

Item 2    THE FORM OF A COMPLIANCE STATEMENT "COMPLIES WITH MS313

          DOC TYPE APPROVAL NO ....................................     Clause
5