Industrial Training (Apprenticeship Training) Amendment Regulations (No. 2) 2006 (WA)

26 May 2006 GOVERNMENT GAZETTE, WA 1873

ED3011*

Industrial Training Act 1975

Industrial Training (Apprenticeship Training)

Amendment Regulations (No. 2) 2006

Made by the Governor in Executive Council.

1.            Citation

These regulations are the Industrial Training (Apprenticeship
Training) Amendment Regulations (No. 2) 2006.

2.             Commencement

These regulations come into operation on 1 June 2006.

3.           The regulations amended

The amendments in these regulations are to the Industrial
Training (Apprenticeship Training) Regulations 1981* .

[* Reprinted as at 2 August 2002.

For amendments to 3 May 2006 see Western Australian
Legislation Information Tables for 2005, Table 4, p. 214 and

Gazette 4 April 2006.]

4. Schedule 1 amended
Schedule 1 is amended as follows:

(a) by deleting the items for —

(i)    Autobody Refinisher;

(ii)    Autobody Repairer;

(iii)    Automotive Electrical Fitting;

(iv)    Engineering Tradesperson (Automotive);

(v)     Engineering Tradesperson (Fabrication);

(vi)    Engineering Tradesperson (Mechanical);

1874 GOVERNMENT GAZETTE, WA 26 May 2006

(vii)      Fuel Injection Fitting;

(viii) Shipwrighting;

(ix)      Shipwrighting and Boatbuilding;

(x) Trimming;

(b) after the item for "Wood Turning" by inserting the following items -

Automotive Electrician	3.5 Years
Automotive Technician Engineering Tradesperson (Fabrication) Engineering Tradesperson (Mechanical) Panel Beater Shipwright and Boatbuilder Vehicle Body Builder Vehicle Painter

(c)

after the item for "Tilelaying" by inserting the following " Vehicle Trimmer ".

4            Schedule 2 amended

Schedule 2 is amended by deleting the items for -

(a)	Automotive Electrical Fitting;
(b)	Fuel Injection Fitting;
(c)	Engineering Tradesperson (Fabrication);
(d)	Engineering Tradesperson (Mechanical);

(e) Shipwrighting;
(f) Trimming.

6.             Schedule 3 amended

Schedule 3 is amended by deleting the item for "Engineering

Tradesperson (Fabrication) Engineering Tradesperson

(Mechanical)".

7.            Schedule 3A amended

(1) Schedule 3A is amended by inserting the following items in the

appropriate alphabetical positions

Engineering	352 hours	352 hours	160 hours
Tradesperson (Fabrication)
Engineering	332 hours	352 hours	160 hours
Tradesperson (Mechanical)
Shipwright and	352 hours	352 hours	160 hours
Boatbuilder

26 May 2006 GOVERNMENT GAZETTE, WA 1875

Automotive	352 hours	352 hours	160 hours
Electrician

Automotive	352 hours 352 hours 160 hours
Technician
Panel Beater	352 hours 352 hours 160 hours
Vehicle Body	352 hours 352 hours 160 hours
Builder
Vehicle Painter	352 hours 352 hours 160 hours
Vehicle Trimmer	352 hours 352 hours 160 hours

(2) Schedule 3A is amended by inserting at the end of the

Schedule -

For the purpose of this Schedule attendance for one day shall be taken to constitute attendance for 8 hours.

8.            Schedule 4 amended

Schedule 4 is amended by deleting the items for -

(a) Automotive Electrical Fitting;

(b) Shipwrighting;
(c) Trimming.

9.           Transitional

(1) Subject to this regulation the Industrial Training

(Apprenticeship Training) Regulations 1981 as in force
immediately before 1 June 2006 continue to apply to and in

relation to -

(a) an apprentice who commenced service in an old trade

under an apprenticeship agreement before 1 June 2006;

or

(b) a person who -

(I) commenced employment as a probationer in an

old trade before 1 June 2006; and

(ii)      completes that probationary employment after 1 June 2006; and

(iii)

on completing that probationary employment agreement,

(an "existing probationer").

(2) The parties to the apprenticeship agreement of an existing

probationer may, with the approval of the Director, agree in the

apprenticeship agreement -

(a) if the probationer was employed in a trade that is also a

new trade, that the apprentice is to be employed in the

1876 GOVERNMENT GAZETTE, WA 26 May 2006

same trade but that the term of the apprenticeship is to

be the new term for that trade; or

(b) that —

(i)     the apprentice is to be employed in a new trade (instead of the old trade in which he or she was employed as a probationer); and

(ii)     the term of the apprenticeship is to be the new term for that new trade.

(3)	If the parties to an apprenticeship agreement agree in the manner described in subregulation (2)(a) or (b), subregulation (1) ceases to apply to and in relation to the apprentice when he or she commences service under the apprenticeship agreement.
(4)	In this regulation — "old trade" means —

(a)	Autobody Refinisher; or
(b)	Autobody Repairer; or
(c)	Automotive Electrical Fitting; or
(d)	Engineering Tradesperson (Automotive); or
(e)	Engineering Tradesperson (Fabrication); or
(f)	Engineering Tradesperson (Mechanical); or
(g)	Fuel Injection Fitting; or
(h)	Shipwrighting; or

(i)     Shipwrighting and Boatbuilding; or

(j) Trimming;

"new term", in relation to a trade, means the term prescribed in

relation to that trade in the Industrial Training
(Apprenticeship Training) Regulations 1981 Schedule 1, as

amended by these regulations;

"new trade" means —

(a)	Automotive Electrician; or
(b)	Automotive Technician; or
(c)	Engineering Tradesperson (Fabrication); or
(d)	Engineering Tradesperson (Mechanical); or
(e)	Panel Beater; or
(f)	Shipwright and Boatbuilder; or
(g)	Vehicle Body Builder; or
(h)	Vehicle Painter; or

(i)     Vehicle Trimmer.

By Command of the Governor,

M. C. WAUCHOPE, Clerk of the Executive Council.