Fair Trading Amendment (Babies' Dummies) Regulation 2008 (NSW)
2008 No 564
New South Wales
Fair Trading Amendment (Babies’
Dummies) Regulation 2008
under the
Fair Trading Act 1987
Her Excellency the Governor, with the advice of the Executive Council, has made the following Regulation under the Fair Trading Act 1987.
VIRGINIA JUDGE, M.P.,
Minister for Fair Trading
Explanatory note
The object of this Regulation is to prescribe the Australian Standard entitled AS 2432:1991, general regulation-making power).
Babies’ dummies as the product safety standard for babies’ dummies.
| Published in Gazette No 157 of 12 December 2008, page 11895 | Page 1 |
| 2008 No 564 | |
| Clause 1 | Fair Trading Amendment (Babies’ Dummies) Regulation 2008 |
Fair Trading Amendment (Babies’ Dummies) Regulation
2008
under the
Fair Trading Act 1987
1 Name of Regulation
This Regulation is the Fair Trading Amendment (Babies’ Dummies)
Regulation 2008.
2 Amendment of Fair Trading Regulation 2007
The Fair Trading Regulation 2007 is amended as set out in Schedule 1.
2008 No 564
Fair Trading Amendment (Babies’ Dummies) Regulation 2008
| Amendment | Schedule 1 |
| Schedule 1 | Amendment |
(Clause 2)
Part 2, Division 16A
Insert after Division 16:
Division 16A Babies’ dummies
68A Definitions In this Division:
AS 2432 means the Australian Standard entitled AS 2432—1991,
Babies’ dummies published by Standards Australia on
15 November 1991.
baby’s dummy means an article used to pacify a baby, that
includes a teat which the baby sucks but from which the babydoes not obtain fluid.
68B Safety standard The product safety standard prescribed for a baby’s dummy is that it must comply with AS 2432.
68C Variation of AS 2432 For the purposes of this Division, AS 2432 is taken to have been amended as follows:
(a) by omitting clauses 3 and 5, (b)
by omitting “Clauses 6.2 and 6.3” from clause 6.1 and inserting instead “Clause 6.2”,
(c) by omitting clause 6.3, (d) by omitting clause 6.4.2 (a), (e)
by omitting “25 mm” from clause 6.4.2 (c) (iii) and inserting instead “15 mm”,
(f)
by omitting “25 mm” from the note following clause 6.4.2 (d) (ii), wherever occurring, and inserting instead “15 mm”,
(g) by omitting the notes to clause 6.4.3, (h) by omitting clauses 7.2–7.4,
2008 No 564
Fair Trading Amendment (Babies’ Dummies) Regulation 2008
| Schedule 1 | Amendment |
(i) by omitting clause 9.1 and inserting instead:
9.1 General The pack shall be legibly labelled with the name and address of the Australian manufacturer or Australian distributor.
(j) by omitting clause 9.3 and inserting instead:
9.3 Warning notice The pack shall bear a clear and legible warning notice which shall include the following word or words that have the same meaning:
WARNING
DO NOT TIE DUMMY AROUND BABY’S NECK AS IT PRESENTS A STRANGULATION HAZARD
In the warning notice the word “PACIFIER” or “SOOTHER” may be substituted for the word “DUMMY”.
(k) by omitting Appendix A, (l)
by omitting clause C2 from Appendix C and inserting instead:
C2 PRINCIPLE A dummy is placed centrally on the test template with its major and minor axes aligned with the major and minor axes of the template and the teat protruding down through the opening. A specified tensile force is applied to the teat in an attempt to force the dummy through the opening in the template. If the dummy is not forced through the opening in the template, the dummy is inverted and the procedure repeated.
(m)
by omitting “AND REAGENT” from clause C3 of Appendix C,
(n)
by omitting “and reagent are” from clause C3 of Appendix C and inserting instead “is”,
(o) by omitting clause C3 (b) from Appendix C,
2008 No 564
Fair Trading Amendment (Babies’ Dummies) Regulation 2008
| Amendment | Schedule 1 |
(p)
by omitting the second paragraph from clause C3 (c) of Appendix C and inserting instead: “The test template shall have inscribed on it the major axis (I) and the minor axis (II)”,
(q)
by omitting “shall be representative of the batch and” from clause C4 of Appendix C,
(r) by omitting clause C6 (c) from Appendix C, (s)
by omitting clause C6 (d) from Appendix C and inserting instead:
(d)
Place the dummy, teat down, in the opening of the template as shown in Figure C2, so that the major axis of the shield aligns with the major axis I-I of the template and the minor axis of the shield aligns with the minor axis II-II of the template.
(t)
by omitting clause C6 (h), (i) and (j) from Appendix C and inserting instead:
(j)
Place the dummy, teat up, in the opening of the template as shown in Figure C3, so that the major axis of the shield aligns with the major axis I-I of the template and the minor axis of the shield aligns with the minor axis II-II of the template.
(u) by omitting clause C6 (m) from Appendix C, (v) by omitting Appendix D,
(w) by omitting “immersed in a wetting solution and then” from clause E2 of Appendix E, (x) by omitting “AND REAGENT” from clause E3 of Appendix E,
(y)
by omitting “and reagent are” from clause E3 of Appendix E and inserting instead “is”,
(z) by omitting clause E3 (c) of Appendix E, (aa) by omitting “shall be representative of the batch and” from
clause E4 of Appendix E,(ab) by omitting clause E6 (b) of Appendix E, (ac) by omitting “While the dummy is wet, clamp” from clause
E6 (c) of Appendix E and inserting instead “Clamp”,(ad) by omitting Appendix F, Appendix G and Appendix H, (ae) by omitting “shall be representative of the batch and” from
clause I4 of Appendix I.
BY AUTHORITY
0
0
0