AD/R44/22 Amdt 3 Main Rotor Blade Leading Edge and Tip Cap Area Skin (Cth)

AIRWORTHINESS DIRECTIVE

On the effective date specified below, and for the reasons set out in the background section, the CASA delegate whose signature appears below revokes Airworthiness Directive (AD) AD/R44/22 Amdt 2 and issues the following AD under subregulation 39.001(1) of CASR 1998.  The AD requires that the action set out in the requirement section (being action that the delegate considers necessary to correct the unsafe condition) be taken in relation to the aircraft or aeronautical product mentioned in the applicability section: (a) in the circumstances mentioned in the requirement section; and (b) in accordance with the instructions set out in the requirement section; and (c) at the time mentioned in the compliance section.

Robinson R44 Series Helicopters

AD/R44/22 Amdt 3 Main Rotor Blade Leading Edge
and Tip Cap Area Skin 8/2008

Applicability:

Model R44 and R44 II model helicopters, with main rotor blades part number C016-2 or C016-5 installed.

Requirement:

1.    Main rotor blades installed on helicopters:

(a)   Inspect the main rotor blade for exposed skin-to-spar bond line, then, using 10x or higher magnification, visually inspect each main rotor blade for skin separation along the leading edge of any exposed (bare metal) blade skin aft of the skin-to-spar bond line on the lower surface of each main rotor blade.

(b)   Perform a “tap test” to detect any separation or void on the skin-to-spar bonded areas on the lower blade skin aft of the skin-to-spar bond line of each main rotor blade using a suitably weighted coin.

(c)   Remove main rotor blade tip cover of each main rotor blade.  Using 10x or higher magnification, visually inspect the blade tip area exposed when the blade tip covers were removed.  “Tap test” the skin-to-cap bond joints on both upper and lower surfaces.

(d)   If the main rotor blade has been found airworthy, refinish the main rotor blade according to the Compliance Procedure, paragraphs 3 through 7, of Robinson R44 Service Letter SL-32 Revision A, dated 29 March 2007.

2.    If any corrosion, separation, or any void is detected by the Requirement 1 inspections, the main rotor blade is not airworthy and must be replaced.

3.    (a)   Visually check for any exposed (bare metal) blade skin aft of the skin-to-spar bond line on the lower surface of each main rotor blade within the outboard 24-inches, paying particular attention to the last 10-inches before the tip.

(b)   Should any exposed (bare metal) blade skin aft of the skin-to-spar bond line on the lower surface of any main rotor blade be found, then Requirements 1(a) through 1(d) of this directive must be accomplished.

Note 1:  Damage to the skin-to-spar bond line may be limited by maintaining a protective coating over the bond line area in accordance with Requirement 1 para (d).

Alternate Method Of Compliance (AMOC)

Airwolf Aerospace LLC Rotor Blade Protective Tape per Supplemental Type Certificate (STC) SR02491CH provides an alternative means of compliance with requirement 3 (a) of this Directive, provided:

1.    At every 100 hour inspection or 12 months time in service, whichever occurs first, the condition of the protective tape is inspected in accordance with Airwolf Aerospace LLC Instructions for Continued Airworthiness, Report
RBPT-100-ICA, Revision 0, dated 18 June 2007 or later FAA accepted revision, and

2.    The applicable “Pilot Operating Handbook and FAA Approved Rotorcraft Flight Manual” is updated to include revisions dated 20 April 2007 or later revisions.

Note 2:  The approval of STC SR02491CH (FAA AMOC to AD 2007-26-12) supersedes the restriction to the installation of “blade tape (anti-erosion tape)” where it exists in the applicable Robinson Maintenance Manuals.

Note 3:  FAA AD 2007-26-12 Amdt 39-15314 dated 18 January 2008 and FAA Approved Alternate Method of Compliance (AMOC) for AD 2007-26-12 refer.

Compliance:

1.    (a) to (c)  Within 10 hours time in service after 18 January 2008, unless already accomplished and thereafter within each 100 hours or 12 months Time In Service (TIS), whichever comes first.

1.    (d)  Whenever the main rotor blade has been found airworthy in accordance with the Requirements of this AD, and if any portion of the skin-to-spar bond line is exposed.

2.    Before further flight.

3.    (a)   Before each flight

3.    (b)   Before further flight

This Directive shall be entered on the maintenance release as maintenance required.  The Requirement 3 (a) visual inspection shall be performed before each flight and may be certified by the Pilot in Command who has been trained to do the inspection by an appropriately qualified person.  In this case, a copy of this Directive is to be carried in the aircraft.

This Amendment becomes effective on 31 July 2008.

Background:

The FAA received eleven reports of main rotor blade disbond, some occurring in flight causing the pilot to experience excessive vibrations and land as a consequence, and some found during routine maintenance.  The actions specified in this Directive are intended to detect blade skin disbond and to prevent blade failure and subsequent loss of control of the helicopter.

This amendment includes reference to STC SR02491CH which is an FAA Approved Alternate Means Of Compliance (AMOC).  As this STC is explicitly mentioned in this Airworthiness Directive, an exclusion request need not be submitted if the requirements of this AD and the STC are followed without variation.

Amendment 2 of this Directive became effective on 3 March 2008.

Amendment 1 of this Directive became effective on 29 February 2008.

The original issue of this Directive became effective on 18 January 2008.

David Villiers
Delegate of the Civil Aviation Safety Authority

17 June 2008