Vehicle Standard (Australian Design Rule – Definitions and Vehicle Categories) 2005 Amendment 3

Administered by Department of Infrastructure, Transport, Regional Development, Communications, Sport and the Arts

Legislation au F2007L03748 Not in force Legislative Instrument

Legislation content

 

 

 

 

 

 

Vehicle Standard (Australian Design Rule –  Definitions and Vehicle Categories) 2005 Amendment 3

 

 

 

Made under section 7 of the Motor Vehicle Standards Act 1989

 

 

 

 

 

 

Explanatory Statement

 

 

 

 

 

 

 

 

 

 

Issued by the authority of the Minister for Transport and

Regional Service

 

 

 

 

 

 

 

 

September 2007

 

 

CONTENTS

 

1. legislative context................................................

2. content and effect of VEHICLE STANDARD (AUSTRALIAN DESIGN RULE - Definitions and Vehicle Categories) 2005 AMENDMENT 3

3. consultation arrangements..........................................

 

 

 

 

 

 

 

 


  1.                        legislative context

Vehicle Standard (Australian Design Rule — Definitions and Vehicle Categories) 2005 Amendment 3 is made under the Motor Vehicle Standards Act 1989 (the Act).  The Act enables the Australian Government to establish nationally uniform standards for road vehicles when they are first supplied to the market in Australia.  The Act applies to such vehicles whether they are manufactured in Australia or are imported as new or second hand vehicles.

The making of the vehicle standards necessary for the Act's effective operation is provided for in section 7 which empowers the Minister to "determine vehicle standards for road vehicles or vehicle components".

Vehicle Standard (Australian Design Rule - Definitions and Vehicle Categories) 2005 Amendment 3 is being made to replace Vehicle Standard (Australian Design Rule - Definitions and Vehicle Categories) 2005 Amendment 2, which was registered on 18 July 2007.

  1.                        content and effect of VEHICLE STANDARD (AUSTRALIAN DESIGN RULE - Definitions and Vehicle Categories) 2005 AMENDMENT 3
    1.                  Overview of the Amendment

This amendment adds a new definition of Twinned Wheels, to clarify the application of technical requirements for vehicles that are of a similar width to motorcycles.

 

  1.                    Effect of the Amendment

 

By adopting a new definition that allows an arrangement of two wheels on the same axle to be treated as one wheel, provided they are spaced no further apart than 460 mm, the amendment has the effect of allowing vehicles complying with this dimensional limit to be classified as motorcycles. Therefore, such vehicles would be subject to all the technical prescriptions applicable to motorcycles rather than motorised tricycles or four wheeled vehicles.

  1.                        consultation arrangements
    1.                  General Consultation Arrangements

It has been longstanding practice to consult widely on proposed new or amended vehicle standards.  For many years there has been active collaboration between the Federal and the State/Territory Governments, as well as consultation with industry and consumer groups.  Much of the consultation takes place within institutional arrangements established for this purpose.  The analysis and documentation prepared in a particular case, and the bodies consulted, depend on the degree of impact the new or amended standard is expected to have on industry or road users.

Depending on the nature of the proposed changes, consultation could involve the Technical Liaison Group (TLG), Transport Agencies Chief Executives (TACE), and the Australian Transport Council (ATC).

  • TLG consists of representatives of government (Australian and State/Territory), the manufacturing and operational arms of the industry (including organisations such as the Federal Chamber of Automotive Industries and the Australian Trucking Association) and of representative organisations of consumers and road users (particularly through the Australian Automobile Association).
  • TACE consists of the chief executives of Australian and State/Territory departments of transport and road vehicle administrations.
  • ATC consists of the Australian, State/Territory and New Zealand ministers with responsibility for transport issues.

Editorial changes and changes to correct errors are processed by the Department of Transport and Regional Services.  This approach is only used where the amendments do not vary the intent of the vehicle standard.

New standards, or significant changes that increase the stringency of existing standards, are subject to a vote by ATC Ministers.  Unless disapproved by a majority of ATC Ministers, the Minister for Local Government, Territories and Roads, can then determine the new or amended standards, under the authority of the Minister for Transport and Regional Services.  Proposals that are regarded as significant need to be supported by a Regulation Impact Statement meeting the requirements of the Office of Best Practice Regulation as published in the Best Practice Regulation Handbook. 

  1.                  Specific Consultation Arrangements for this Amendment

Specific consultation arrangements for this amendment are detailed in the Regulation Impact Statement for New Definition for Twinned Wheels for Inclusion in Vehicle Standard (Australian Design Rule — Definitions and Vehicle Categories) 2005.

Overview

The Vehicle Standard (Australian Design Rule – Definitions and Vehicle Categories) 2005 Amendment 3, enacted in 2007 under section 7 of the Motor Vehicle Standards Act 1989, was introduced to address the need for a more precise definition of "twinned wheels" to clarify the application of technical requirements for vehicles that share a similar width to motorcycles. This amendment aims to ensure that vehicles with two wheels on the same axle, spaced no further apart than 460 mm, are classified as motorcycles, thereby subjecting them to the same technical prescriptions applicable to motorcycles instead of motorised tricycles or four-wheeled vehicles. The Australian Government, through the Minister for Transport and Regional Services, initiated this amendment to maintain uniformity and safety standards in the automotive industry, both for domestically manufactured and imported vehicles. The process involved extensive consultation with various stakeholders, including federal and state/territory governments, industry representatives, and consumer groups, to ensure the amendment aligns with the overarching policy objectives of the Act.

Scope and Application

The Vehicle Standard (Australian Design Rule – Definitions and Vehicle Categories) 2005 Amendment 3 applies to road vehicles supplied to the Australian market, regardless of whether they are manufactured domestically or imported as new or second-hand vehicles. This amendment falls under the Motor Vehicle Standards Act 1989, which empowers the Minister to establish and enforce vehicle standards for road vehicles and vehicle components. The amendment introduces a new definition of "Twinned Wheels" to clarify the application of technical requirements for vehicles similar in width to motorcycles, thereby allowing vehicles with two wheels spaced no more than 460 mm apart to be classified as motorcycles. This classification means such vehicles will be subject to the technical prescriptions applicable to motorcycles rather than motorised tricycles or four-wheeled vehicles. The geographic reach of this amendment is national, as it pertains to vehicles throughout Australia, and it extends to both imported and domestically manufactured vehicles. The amendment is subject to consultation processes involving various stakeholders, including the Technical Liaison Group, Transport Agencies Chief Executives, and the Australian Transport Council, to ensure broad agreement and implementation.

Key Provisions

The Vehicle Standard (Australian Design Rule – Definitions and Vehicle Categories) 2005 Amendment 3, as enacted under section 7 of the Motor Vehicle Standards Act 1989, introduces a new definition for "Twinned Wheels" (section 1(1)). This amendment aims to clarify the application of technical requirements for vehicles that are of a similar width to motorcycles. Specifically, it allows an arrangement of two wheels on the same axle to be treated as one wheel, provided they are spaced no further apart than 460 mm. This definitional change permits vehicles that meet this dimensional limit to be classified as motorcycles, subjecting them to the technical prescriptions applicable to motorcycles rather than those for motorised tricycles or four-wheeled vehicles. The obligations under this amendment primarily involve ensuring that vehicles meeting the new definition for twinned wheels are correctly classified and comply with the relevant technical standards for motorcycles. Vehicle manufacturers and importers must ensure that their vehicles adhere to the dimensional specifications outlined in the amendment, thereby facilitating their classification and compliance with applicable regulations. This also extends to ensuring that all necessary documentation and technical submissions are accurately reflecting the vehicle's compliance with the new standards. Failure to comply with the provisions of the Vehicle Standard (Australian Design Rule – Definitions and Vehicle Categories) 2005 Amendment 3 can lead to various legal consequences. Under the Motor Vehicle Standards Act 1989, non-compliance with vehicle standards can result in civil penalties, including fines. The exact penalties are not specified in the explanatory statement but are generally in accordance with the penalties outlined in the Act. Additionally, there may be criminal penalties for more severe breaches, which could include imprisonment depending on the severity and intent of the non-compliance. The precise penalties and enforcement actions are determined by the relevant authorities, such as state or territory transport departments, in accordance with the legislative framework provided by the Motor Vehicle Standards Act 1989.

Legal classification tags

Area of Law
Commercial Law
Instrument
Regulation
Concepts
Definitions & Interpretation
Consultation Requirements
Regulatory Standards

Interactions

Authorises

All Versions

Sourced from the Federal Register of Legislation at 26 August 2026. For the latest information on Australian Government law please go to https://www.legislation.gov.au.