Medical Device Standards Order (Standards for Risk Management) 2008

Administered by Department of Health, Disability and Ageing

Legislation au F2008L01699 Not in force Legislative Instrument

Legislation content

EXPLANATORY STATEMENT

 

Subject:  MEDICAL DEVICE STANDARDS ORDER (STANDARDS FOR RISK MANAGEMENT) 2008 

 

Section 41CB, Therapeutic Goods Act 1989

 

OUTLINE

 

Medical Device Standards Order (Standards for Risk Management) 2008 (MDSO 2008) is an Order made by the delegate of the Minister for Health and Ageing under section 41CB of the Therapeutic Goods Act 1989 (the Act).  Section 41CB of the Act authorises the Minister, or her delegate, to determine appropriate medical standards that are applicable to kinds of medical devices and to determine that medical devices that comply with those standards are to be treated as complying with those parts of the essential principles specified in the standards.

 

MDSO 2008 revokes and replaces Medical Device Standards Order No. 2 – Medical Device Standards for Risk Management (MDSO 2 of 2003) that was made on 20 February 2003 and commenced upon its gazettal on 5 March 2003.  MDSO 2 of 2003 specified particular standards as medical device standards for risk analysis and risk management methods concerning medical devices. 

 

MDSO 2008 introduces new and updated standards (or parts of these standards) published by standards organisations that are relevant to risk analysis and risk management methods for medical devices in order to demonstrate compliance with the essential principles.  The standards set out in MDSO 2008 are the following:

  • EN ISO 14971: 2000 Medical Devices – Application of Risk Management to Medical Devices;
  • ISO 14971: 2000 Medical Devices – Application of Risk Management to Medical Devices (which is identical to EN ISO 14971: 2000);
  • EN ISO 14971: 2007 Medical Devices – Application of Risk Management to Medical Devices; and
  • ISO 14971: 2007 Medical Devices – Application of Risk Management to Medical Devices (which is identical to EN ISO 14971: 2007)

 

Electronic or hard copies of these standards can be purchased on-line from SAI Global Limited at the following website: http://www.saiglobal.com.

 

The Order was signed by the delegate to the Minister on 19 May 2008 and commenced on the day after it was registered on the Federal Register of Legislative Instruments.

 

BACKGROUND

 

The Act provides for the establishment and maintenance of a national system of controls relating to the quality, safety and efficacy of therapeutic goods that are used in Australia (whether manufactured in Australia or elsewhere) or exported from Australia.

 

Section 41CB of the Act authorises the Minister, or the Minister’s delegate, by order,                                      to determine medical device standards for kinds of medical devices identified in that determination and to also determine that medical devices that comply with these standards are to be treated as complying with those parts of the essential principles specified in that determination.   That determination is made in the form of an order.

 

The essential principles set out the requirements relating to the safety and performance characteristics of medical devices that must be complied with before a device can be imported, supplied or exported. Compliance with applicable medical device standards is not required, but it is one way to establish compliance with the essential principles. If a manufacturer chooses to apply a specified medical device standard, and this is applied correctly to a device, the device is presumed to comply with the parts of the essential principles set out in the MDSO 2008 (section 41BH of the Act).

 

MDSO 2008 determines medical device standards, which set methods for risk analysis and risk management in order to demonstrate compliance of medical devices with the essential principles.

 

CHANGES TO STANDARDS

 

International ‘ISO’ and ‘EN’ device standards are living documents that are developed and constantly being updated by groups of international experts.  Australian representatives are involved in some of these committees.  There is extensive consultation on the ISO and EN standards during their development and subsequent review.  With both industry and the TGA seeking to optimise Australia’s position in the global device market, it is imperative that Australia’s standards do not fall out of step with the international market.

 

Updates to international device standards reflect changes to international best practice as well as the emergence of new technologies and new manufacturing procedures.  Where relevant the latest international standards are adopted by leading regulators including Australia, Europe, the USA and Canada.

 

Australia will very quickly fall behind if it fails to adopt the latest international standards.  In the longer term not keeping up with changes to the relevant international standards will lead to a unique regulatory system in Australia, making regulatory compliance more difficult and costly for importers and/or exporters of medical devices into Australia.  The updated standards referenced in MDSO 2008 reflect the current relevant international standards for clinical investigation.

 

Transition to the updated 2007 standards

 

EN ISO 14971:2000 and ISO 14971:2000 have been replaced by EN ISO 14971:2007 and ISO 14971:2007 respectively.  It is proposed that industry be given up until 31 March 2010 to comply with the updated 2007 standards.  This time period is aligned with the European transition times for meeting the new standard.

 

CONSULTATION

 

Key industry stakeholders including the Medical Industry Association of Australia (now the Medical Technology Association of Australia), the Australian Dental Industry Association and AusBiotech were consulted on the adoption of an updated version of MDSO 2 of 2003 during April-June 2007 in preparation for the move to a joint regulatory scheme under the proposed Australia New Zealand Therapeutic Products Authority (ANZTPA).  Industry groups supported the adoption of these standards. 

 

With the postponement of ANZTPA the updated drafts used during the ANZTPA consultation have been amended so that they reference the current Therapeutic Goods (Medical Devices) Regulations 2002 instead of the draft ANZTPA Medical Devices Rule 2007.  There was a further round of stakeholder consultation on MDSO 2008 from 21 December 2007 to 15 February 2008.  Industry groups supported the adoption of the Order which references the latest international standards for risk management.

 

REGULATION IMPACT STATEMENT

 

Compliance with the proposed medical device standards is voluntary and members of industry may choose alternative means to demonstrate compliance with the Essential Principles.  All stakeholders, including industry and Standards Australia have been consulted during the development of the proposed new regulatory system for medical devices.  There was overall support for the adoption of international standards.  The Office of Regulation Review assessed the proposal for voluntary standards and, as it is not prohibitive either in terms of costs or time delays, the proposal is considered to be non-regulatory and as such a Regulatory Impact Statement is not required.

 

APPLICATION OF THE LEGISLATIVE INSTRUMENTS ACT 2003 (THE LIA)

 

Under paragraph 6(d)(i) of the LIA, an instrument is a legislative instrument for the purposes of section 5 of the LIA if it is declared to be a disallowable instrument under legislation in force before the commencement of the LIA.  This determination is a legislative instrument and it is subject to tabling and disallowance in the Parliament under sections 38 and 42 of the LIA, respectively.

 

 

 

 

Interactions

Authorises

All Versions

Sourced from the Federal Register of Legislation at 26 August 2026. For the latest information on Australian Government law please go to https://www.legislation.gov.au.